14
15
LIGHTING THE GRILL USING THE IGNITER
WARNING!
• Open the grill fully before lighting the burner to prevent an explosion from
gas buildup.
•
Always inspect the regulator/tube assembly before each use. If it is
bent, cut or damaged, do not use the LP gas grill. Contact the manufacturer, as the
regulator assembly must be replaced with an assembly specified by the manufacturer
prior to the further use of the LP gas grill.
HOW TO LIGHT YOUR LP GAS GRILL (See diagram below for illustrations)
Note:
If the flame is accidentally extinguished, repeat the procedure below for lighting the
grill. (See also TROUBLESHOOTING on pages 24 – 25.)
1) Open the lid and rotate the level adjusters to the grilling position desired.
2) Push in and turn the regulator knob counterclockwise from the OFF/ LOCK position to
HIGH.
(FIG 15A)
3) Push the igniter button several times so that it clicks each time.
(FIG 15B)
4) Turn the regulator knob from HIGH to LOW, while checking the flame through the
match light hole to make sure it is lit.
5) If burner does not light or igniter does not work, turn regulator knob to OFF/LOCK.
Remove the cooking surface to dissipate the gas. Wait five minutes then repeat
steps 2 thru 4.
6) If burner still fails to light, repeat step 5, wait five minutes and refer to the
TROUBLESHOOTING page. If it fails to light, the burner can be lit manually, see
MANUAL LIGHTING OF THE GRILL on page 16.
7) After ignition, preheat the grill and cooling surface by turning the regulator knob
to HIGH for about 8 minutes.
WARNING: If the burner goes out while cooking, turn the regulator knob
to the OFF position. Wait five minutes before attempting to relight the grill.
MANUAL LIGHTING OF THE GRILL
Note:
If the flame is accidentally extinguished, repeat the procedure below for lighting
the grill. (See also TROUBLESHOOTING on pages 24 – 25.)
Fig. 15a
Fig. 15b
•
WARNING! Never attempt to repair or refill a 1# LP gas cylinder and its
valve.
These could cause a hazard or explosion. Replace gas cylinder with
a spare.
• When transporting an LP gas cylinder, keep it secured in an upright position with the
protective cap on.
CONNECTING/ DISCONNECTING LP GAS CYLINDER TO GRILL
• Always check for gas leaks when you disconnect and reconnect the regulator to the
LP gas cylinder, especially after a period of storage (for example, over winter).
• Check tubes that lead into the burner for any blockage from insects, spiders, or food
grease before using.
• Check regulator tube for bends or crimping.
• Check tube nozzle and threaded collar for damage.
REGULATOR ASSEMBLY
WARNING!
Using a regulator assembly that has not been supplied by the manufacturer of
this LP gas grill, could result in serious bodily injury or property loss.
The LP gas cylinder shall be constructed and marked in accordance with the
specifications for LP gas cylinders of the Department of Transportation (DOT).
• Use only regulator assembly that has been furnished with this LP gas grill. If the
regulator assembly is not working properly and you need a replacement, contact the
manufacturer at (1-800-231-9786).
• Inspect the regulator assembly before each use. If it is bent, cut or damaged, do not
use the LP gas grill. Contact the manufacturer, as the regulator assembly must be
replaced with an assembly specified by the manufacturer prior to the further use of the
LP gas grill.
PREPARATION BEFORE COOKING
• Wash the cooking surface with a mixture of hot water and dish detergent. Do not use
an abrasive scrubber. This product is Teflon coated and harsh cleansers will ruin the
finish.
• Empty the grease tray after each cooking session so excessive grease does not
accumulate. Wash same as cooking surface.
• Make sure grease tray is in place before each grilling session.
(FIG 14)
WARNING!
• Empty the grease tray after each cooking session so excessive grease does
not accumulate. Failure to remove grease may result in a grease fire in the
tray or bowl.
• Never light the LP gas grill without the grease tray in place.
Fig. 14
