Geneva TOURING L, Quick Start Manual

Page: 4 / 24

6 7
3.After a few seconds the display will show the RDS information.
DAB / DAB+
1.Press
until the display shows “DAB/DAB+”.
2.Select a DAB station with and . TOURING L is compatible with DAB, DAB+, DMR and DMB.
When using your TOURING L for the first time, the radio needs to find available radio stations in your region (a scan function). After
a SCAN, the stations will be automatically stored.
• Hold down the button until “SCAN” displays. The indication will blink for a few seconds, then the display will confirm that
the first station has been found.
“SCAN” is also needed after traveling to a new location that provides different radio stations, or when you move the radio to a
different room with a different radio reception.
Presets
You can save six FM stations plus six DAB stations. To save a preset:
1. Select the station you want to save.
2. Long press
until the display shows “PRESET 1” as blinking.
3. If you want to save using a different PRESET number, press again and select the desired number.
4. After, long press to save the station.
To recall a preset:
1. Short press . The display will show the first saved preset. If a saved
station is playing , the display will show the next saved preset.
2. If you want to recall a different station, press
again.
3. Wait two seconds and the unit will play the selected preset station.
Line-in
To connect a source device to your TOURING L, you need a stereo audio cable with 3.5mm jack plug connector.
1. Connect the cable to the audio source device (headphone or line-out plug).
2. Connect the other end of the cable to the line-In socket on the back of the TOURING L. The unit will automatically change mode
to LINE IN.
3. By disconnecting the cable from TOURING L, the unit will return to the previously selected mode.
Bluetooth
Mobile phones and computers with Bluetooth can connect to the TOURING L and play music. The mobile phone or computer must
support Bluetooth A2DP.
Initial set-up (“pairing”):
1. Press the key. The display will show “BLUE”. Wait for 20 seconds until the display shows “PAIRING” as blinking .
2. Select “settings” on your mobile phone. Select “General/Bluetooth”. Turn on Bluetooth. New Bluetooth devices are discovered
automatically (on some devices you will need to press ‘scan’).
3. After a few seconds, “TOURING L” will appear.
4. Select “TOURING L”. The mobile phone is now connecting (“pairing”) to the TOURING L.
I have an unreliable connection via Bluetooth and there are dropouts.
• Move the mobile phone closer to the TOURING L.
• Move or turn off other wireless devices that can disturb a Bluetooth connection (for example Wi-Fi, other mobile phones etc).
How do I know if the battery is charging?
A small dot on the lower right of the display will turn on if the battery is being charged.
When the charger is being connected the display will also show “CHARGE”.
How can I check the battery
charge?
A dot on the lower right corner of the display shows the battery status:
• OFF: battery fully charged.
• Blinking: battery is low.
When the battery is low, the volume will automatically be limited to 50. The unit can still play music for some minutes.
If the battery is empty, the display will show “LOW BATT” and TOURING L will automatically turn off.
Display shows ‘NO DAB SERVICE’ or ‘NO DAB SIGNAL’
Extend the antenna. You may have to experiment different positions to find the best reception. Positions higher up or nearer win-
dows may improve reception.
RT
More information, troubleshooting, etc: select “Support” at www.genevalab.com.
Service and repair
If the product is damaged and needs repair, please contact your dealer. Visit www.genevalab.com to find a dealer in your area.
Warranty
See the specific terms for your country at www.genevalab.com.
5. If the mobile phone asks for a PIN, enter “0000” (four zeros).
6. You can now play music on your mobile phone and listen to it on the TOURING L.
Playing music
Most mobile phones will connect automatically to the TOURING L after initial set-up (“pairing”).
1. Be sure the Bluetooth setting on your mobile phone is ON.
2. Press the key. The display will show “BLUE”, then will show “SEARCH”, as blinking.
3. After a few seconds, TOURING L will automatically connect to your mobile phone. The display will show “CONNECT”.
4. Play music on the mobile phone and the music will start playing on the TOURING L automatically after a few seconds.
TROUBLESHOOTING
Why is my mobile phone not connecting?
You will find more detailed information on various mobile phones on our support pages at www.genevalab.com.
The TOURING L will not turn on, and the display shows “LOW BATT”.
The battery is slow on charge.
Connect the power adapter to the TOURING L and the battery will begin charging. You can use the TOURING L while the charger
is connected.
The TOURING L will not turn on, and nothing happens.
If the battery is very low, there will not be enough power to even turn on the display. TOURING L can be turned on after it has been
connected for a short while to the power adapter.
Why is the TOURING L turning off after a while?
After a few minutes of inactivity, the device will automatically turn itself off to save battery.
What is the pin for a Bluetooth connection?
The PIN is 0000 (four zeros). Not all computers or mobile phones require a pin code during initial set-up (pairing ).