background image

PRINTED IN U.S.A

1-7 

0

908147

/0

9

99

Cut along dotted line and retain for Dealer

’s records.

CHECKLISTS

Pre-Delivery Checklist

Delivery Checklist

The following checklist is an important reminder of valuable
information and inspections which MUST be made before
delivering the machine to the customer.  Check off each item
after prescribed action is taken.

CHECK THAT:

Unit has NOT been damaged in shipment.  Check for
such things as dents and loose or missing parts; correct
or replace components as required.

Battery is securely mounted and NOT cracked.  Make
sure cable connections are tight.

Cylinders, hoses and fittings are not damaged, leaking or
loosely connected.

Filters are not damaged, leaking or loosely secured.

Machine is properly lubricated and no grease fittings are
missing or damaged.

Hydraulic system reservoir, engine crankcase and drive
chaincases are filled to their proper levels.

All adjustments are made to comply with settings given
in Section 4–Maintenance of this manual.

All guards, shields and decals are in place and secured.

Model and serial numbers for this unit are recorded in
the space provided on this page and on page 1-1.

IMPORTANT: Start the engine and test run the unit
while checking that all controls operate properly.

CHECK THAT:

Drive controls and boom/arm/bucket/swing/pivot 
controls operate properly and are not damaged or 
binding.

Drive controls are properly adjusted for a correct neutral
position.

The parking and travelling gear brake, along with the
blocking devices, are automatically activated with unit
stationary (no pilot control pressure).

All hydraulic functions are NOT operational with the
left-hand control console in the pivoted rearward 
position.

I acknowledge that pre-delivery procedures were performed
on this unit as outlined on this page.

Dealership Name

Dealer Representative Name

Date Checklist Filled Out

Model & Serial Number

The following checklist is an important reminder of valuable
information that MUST be passed on to the customer at the
time of delivery.  Check off each item as you explain it to the
customer.

EXPLAIN:

The Safety Information and Operation chapters of this
manual, regarding the safe operation of this machine.

The Maintenance and Troubleshooting chapters for
information regarding the proper maintenance of this
machine.  Explain that regular lubrication and mainte-
nance is required for continued safe operation and long
machine life.

Give the Operator’s Manual to the customer and instruct
the customer to read and completely understand the con-
tents before operating the unit.

Explain that the customer MUST consult the engine
manual (provided) for related specifications, operating
adjustments and maintenance instructions.

Completely fill out the Owner’s Registration, including
customer’s signature and return it to the Gehl Company.

Customer’s Signature

Date Delivered

Retain for Dealer’s Records

Summary of Contents for GE 802





















































Reviews: