GEA Hilge HYGIA ADAPTA Operating Instruction Download Page 81

Page: 81 / 96

10.4.15 Installing tandem double mechanical seal

Equipment and tools from the GEA Hilge assembly tool kit

•

Spray bottle

•

Plastic mounting sleeve

•

Mounting sleeve

•

Loctite Type 243

•

Klüber paste UH1 96-402

•

Extractor

•

Socket wrench with plastic insert

Installing tandem double mechanical seal

Screw set screws (0904.02) one or two turns into
the adjusting ring (0516.00) and wet with Loctite
243.

Fig.85:

Adjusting ring

Push the adjusting ring (0516.00) to the correct
position on the shaft, using a suitable measuring
tool.
Lock the adjusting ring (0516.00) with the set
screws (0904.02).

Fig.86:

Position of the adjusting
ring

Relieve the spring of the mechanical seal
(0433.01) against the adjusting ring (0516.00),
using the extractor.

Fig.87:

Extractor

Malfunctions / repairs

Repair

BA.H2A.ADY.002.GB_1

18.12.2017

Summary of Contents for Hilge HYGIA ADAPTA

































































































Search results

Summary of Contents for Hilge HYGIA ADAPTA

Reviews:

Brands by name

Popular brands

GEA Hilge HYGIA ADAPTA, Operating Instruction

Search results

Summary of Contents for Hilge HYGIA ADAPTA

Reviews:

Brands by name

Popular brands