manualshive.com logo in svg

GEA Hilge HYGIA ADAPTA, Operating Instruction

Share
Download
GEA Hilge HYGIA ADAPTA Operating Instruction Download Page 30

Vertical assembly

0.75

> 7.5 hp

- 5 hp

1

2

 i

n

4

0

 i

n

Fig.7:

Minimum distances in vertical assembly

Settings for the 3-A assembly

Installation height of the pump

To ensure proper cleaning of the pump environment, the 3-A stand must have a
minimum height. The dimension is shown in the following figure.

B

Fig.8:

HYGIA on 3-A stand

Dimension B: at least 4" (102 mm)

Screw-in depth of the feet

 

Notice!

 

Hygiene risk, food safety

Feet which are improperly sealed provide space for hidden contaminants.
► Screw in the feet so that the O-ring rests on the smooth counterpart.

6.3.3.2 Noise and vibration damping

To achieve optimum performance and to minimize noise and vibration, it is
recommended to provide the pump with vibration dampers.

Assembly and installation

Setup, installation, and connection

 

BA.H2A.ADY.002.GB_1

30

18.12.2017

Summary of Contents for Hilge HYGIA ADAPTA

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands