manualshive.com logo in svg

GEA Hilge HYGIA ADAPTA, Operating Instruction

Share
Download
GEA Hilge HYGIA ADAPTA Operating Instruction Download Page 23

The noise emissions caused by a pump are influenced mainly by its application.
The values shown here should therefore be considered merely as a guide.

5.4

Maximum operating temperatures

Warning!

 

Exceeding the maximum temperatures!
► Never exceed the specified operating temperatures.

Operating temperatures

Design

Temp. [°C/°F]

Normal version

95 / 203

Sterilisation (SIP)

140 / 284

Variations are possible at the above temperatures.

5.5

Maximum operating pressure

Warning!

 

Pressure overload of the pump!
► Operate the pump according to the ordering data.
► Never exceed the specified maximum operating pressures.

The pump’s maximum operating pressure pump depends on various factors:

•

Pump type

•

Type of connections

•

Type of mechanical seal.

5.6

Resistance of Sealing Materials

The resistance of sealing materials depends on the type and temperature of the
medium conveyed. The exposure time can adversely affect the service life of the
seals. The sealing materials comply with the regulations of FDA 21 CFR
177.2600 or FDA 21 CFR 177.1550.

Resistance:

•

+ = good resistance

•

o = reduced resistance

•

- = no resistance

Sealing resistance table

Medium

Temperature

Gasket material
(general operating temperature)

 

 

EPDM
-40...+135°C
(-40...275°F)

FKM
-10...+200 °C
(+14...+392°F)

Caustics up to 3%

up to 80 °C (176°F)

+

o

Caustics up to 5%

up to 40 °C (104°F)

+

o

Technical data

Maximum operating temperatures

BA.H2A.ADY.002.GB_1

 

18.12.2017

23

Summary of Contents for Hilge HYGIA ADAPTA

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands