GE UFC 207 Owner'S Manual Download Page 2

2

A. INTRODUCTION

B. SAFETY WARNINGS

It is important to read and understand the following safety
warnings to ensure reliable service from your System.

By purchasing the Homespring™ Water Purifier System,
you have taken the first step in providing safer, great
tasting water in the entire home.

The Homespring™ Water Purifier System (the System) is
an advanced Point of Entry (POE) water filtration system
that uses ultrafilter membrane technology to provide a
physical barrier to bacteria, parasites, viruses, and
particles. The System requires minimal maintenance and
will provide you with years of cleaner, safer, better tasting
water. Simply follow the information found in this manual
and schedule an annual maintenance visit with your
Homespring™ Dealer.

The System must be installed in strict compliance with
provincial or state laws and local laws and regulations.
The System conforms to ANSI/NSF 42 and 53 for the
specific performance claims as verified and substantiated
by test data. The System should only be used to filter
water less than 100

o

F (38

o

C) and must be protected from

freezing.

Thank You!

Legal Disclaimer

GE Water & Process Technologies

3239 Dundas Street West
Oakville, ON, Canada
L6M 4B2

www.homespring.com

Manufacturer’s Contact Information

This manual outlines some of the basic principles of
household water collection, treatment, and discharge and
some of the features of the 

Homespring™ Water Purifier

System

. It is not intended to be a definitive dissertation on

the principles set out above, nor is it intended to be relied
upon by anyone but 

Homespring™ Customer Care

(“Consultants”) and 

 Qualified Technicians

. Any other

reliance is expressly excluded.

The 

Homespring™ Water Purifier System

 must be

installed by a 

Homespring™ Authorized Technician

 and

properly maintained in accordance with the Operations
and the Owner’s Manual. Failure to properly maintain the
System will compromise performance and/or result in the
failure to control water quality.

Servicing Information

All service and maintenance must be performed by a
Homespring™ Authorized Technician. Should service be
required during or after the warranty period, or should you
have any questions regarding how to use your
Homespring™ Water Purifier System, please contact your
Homespring™ Dealer.

Read this manual carefully prior to using the
System.

Permanently locate this manual near the System
for future references.

Periodic checks of the System are required to
ensure safe and efficient operation.

Annual maintenance by a Homespring™

           Qualified Technician is required to validate the
             limited warranty.

Cost of all maintenance visits is the Owner’s
responsibility.

Most tools referenced in this manual are available
through your Homespring Dealer.

During servicing of the System, water supply in
your home will be temporarily interrupted.

IMPORTANT! - Read First

Dealer and System Information

Dealer’s Name

Dealer’s Phone Number

Model Number

Qualified Technician

Homespring™ Customer Service
Number 1-866-418-7412

Emergency Customer Service Number

Membrane Module Serial Number

Backpulse Tank Serial Number

Backpulse Tank Pressure Setpoint

Installation Date

Summary of Contents for UFC 207
























Reviews: