GE TruTrak+ 3900 User Manual Download Page 4 | Manualshive

Page: 4 / 107

background image

Important

Rx Only (USA)

Attention! Consult the accompanying instructions before using this
device.

The safety, reliability, and performance of this device can be assured only under
the following conditions:

•

If it is used according to the accompanying operating instructions.

•

If fittings, extensions, readjustments, changes, or repairs are carried out by
agents authorized by Datex-Ohmeda.

•

If it is used in buildings having ground equalization wiring that complies with
relevant local standards and regulations.

This device must be cleaned and checked periodically. Do not use a defective
device. Parts that are broken, missing, plainly worn, distorted, or contaminated
should be replaced immediately. If repair or replacement becomes necessary,
request service advice from Datex-Ohmeda. Do not repair this device or any of its
parts other than in accordance with written instructions provided by Datex-
Ohmeda.

The user of this device shall have the sole responsibility for any malfunction that
results from improper use, faulty maintenance, improper repair, unauthorized
service, damage, or alteration by anyone other than Datex-Ohmeda.

Trademarks

Datex®, Ohmeda®, OxyTip®, PerfTrak®, TeleOximetry®, TruTrak®, and PI

r

® are

the property of GE Healthcare Finland Oy. All other product and company names
are the property of their respective owners.

0537

GE Healthcare Finland Oy
Helsinki, Finland
+358 10 394 11
www.gehealthcare.com

© 2005 General Electric Company. All rights reserved.

«
...
2
3
4
5
6
...
»

Summary of Contents for TruTrak+ 3900












































































































Reviews:

No comments

Related manuals for TruTrak+ 3900

Brand: Varec Pages: 74

Brand: Halyard Pages: 84

Brand: PAIDI Pages: 48

Brand: ParaBody Pages: 5

Brand: Baileigh Industrial Pages: 28

Brand: Baileigh Industrial Pages: 56

Brand: Jacobsen Pages: 20

Brand: OHAUS Pages: 84

Brand: TC Electronic Pages: 67

Brand: Tascam Pages: 3

Brand: ubicquia Pages: 4

Brand: ABB Pages: 136

Brand: ABB Pages: 108

Brand: Beckman Coulter Pages: 52

Brand: Copernicus Pages: 13

Brand: SDE Lighting Pages: 7

Brand: XPOtool Pages: 4

Brand: Harken Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands