GE TruTrak+ 3900 User Manual Download Page 56

Page: 56 / 107

3900/3900P User’s Manual

3-8

Condition

Possible cause(s)

Recommended action(s)

No communication
through the modem.

Incorrect cable used to connect
modem to monitor.

Modem is powered off or not
properly connected. Phone line
failure.

Incorrect or improperly entered
modem initialization string.

Your phone system may require a
guard tone.

Mismatched baud rate. For some
older modems, the baud rate for
the oximeter must be set to match
the baud rate for the modem.

Modem failure.

You must use the Datex-Ohmeda
modem/analog cable.
Refer to

Parts list

in chapter 6.

Check and correct all modem
connections. Power on the modem.
Check the phone line.

Check initialization string entry.
Verify the accuracy of the string. See

Modem setup

in chapter 5.

Enter a guard tone, if needed. See

Modem setup

in chapter 5.

Set the oximeter baud rate to match
the modem baud rate. See

SETTINGS

in chapter 2.

Contact the manufacturer of the
modem for assistance.

Data transmission from
the oximeter is very slow
or fails repeatedly.

The data transfer rate of the
modem connected to the oximeter
is too low.

Use a 56K modem.

Summary of Contents for TruTrak+ 3900












































































































Search results

Summary of Contents for TruTrak+ 3900

Reviews:

Related manuals for TruTrak+ 3900

Brands by name

Popular brands

GE TruTrak+ 3900, User Manual

Search results

Summary of Contents for TruTrak+ 3900

Reviews:

Related manuals for TruTrak+ 3900

Brands by name

Popular brands