GE EV100 LX Instructions Manual Download

Page: 67 / 81

location " Y " on the control card. After installing the handset

tool, plug in the battery and turn on the key switch. The

following is the start-up display sequence that will occur:

START-UP DISPLAY SEQUENCE

Key Switch on

Verify Display Segments for

one second

8888

BDI Display

Diagnostics

override

Blank Display

with fault

( No BDI used )

Run Mode

BDI Display

Diagnostics

override

Blank Display

with fault

( No BDI used )

Key Switch Off

Display traction

hourmeter for

four seconds

Display pump

hourmeter for

four seconds

Blank

( If no Pump SCR used )

NOTE: The vehicle can be operated with the handset

connected,

however, the adjustment knob must be set

fully clockwise to insure the control operates at top

speed.

INSTRUCTIONS

EV100 HANDSET

GENERAL

The Handset is a multi-functional tool to be used with the

EV100/200 LX and LXT SCR controls. The Handset consist

of a Light Emitting Diode (LED) display and a keyboard for

data entry.

PURPOSE:

The purpose of the Handset is to allow

authorized personnel

to perform the following functions:

Monitor existing system fault codes for both traction

and pump SCR systems

Monitor intermittent random status code

Monitor battery state of charge on LXT systems

Monitor hourmeter reading on traction and pump

SCR systems

Monitor or adjust the following control functions:

Creep speed

Controlled Acceleration and 1A time

Current Limit

Steer pump time delay and define signal input

( seat switch or directional switch )

Plugging distance (Current)

Pedal position plug range or disable

1A drop out current or disable

Field Weakening drop out

Field Weakening pick up

Regen braking current limit

Regen braking drop out

Speed limit points ( SL1,SL2, and SL3)

Truck Management fault speed limit

Internal resistance compensation for battery

state of charge indication

Battery voltage ( 36/48 volts is auto ranging )

Selection of card operation type:

Standard traction card selection:

Standard traction with Field Weakening

Standard traction with speed limits

Standard traction with Regen/Field Weaken-

ing

High or low current limit for all of the above.

OPERATION:

Warning : Before connecting or disconnecting the hand-

set tool, jack up the drive wheels of the vehicle, turn off

the key switch, unplug the battery and discharge the

capacitors.

At the SCR control traction card, unplug the " Y plug " if the

dash display is in use and plug in the handset to the plug

GEH-5716

September 1993

GE Electric Vehicle

Systems

Summary of Contents for EV100 LX


















































































Search results

Summary of Contents for EV100 LX

Reviews:

Related manuals for EV100 LX

Brands by name

Popular brands

GE EV100 LX, Instructions Manual

Search results

Summary of Contents for EV100 LX

Reviews:

Related manuals for EV100 LX

Brands by name

Popular brands