GE ApexPro Service Manual Download Page 81 | Manualshive

Page: 81 / 202

background image

Revision C

ApexPro Telemetry Server

3-25

2001989-178

Installation: Remote Services Configuration

3.

Click Save to apply configuration setting changes.

Parameter

Value

Notes

HTTP Proxy Server Configuration

Address

Installation site proxy
server IP address.

Value determined
during site survey.
Refer to site survey
workbook.

Port

Installation site proxy
server port number.

Value determined
during site survey.
Refer to site survey
workbook.

Username/Password

Enter Username/
Password required as
required for
authentication.

Value determined
during site survey.
Refer to site survey
workbook.

Scheme

Select the correct
scheme from the drop-
down list. The drop-down
list schemes are Basic,
Digest and NTLM.

Value determined
during site survey.
Refer to site survey
workbook.

DNS Server IP Addresses

Preferred DNS Server

Displays installation site
preferred DNS server IP
address (optional).

Value determined
during site survey.
Refer to site survey
workbook.

Alternate DNS Server

Displays installation site
alternate DNS server IP
address (optional).

Value determined
during site survey.
Refer to site survey
workbook.

Remote Service Configuration

System ID

Identifies system to
remote service.

Read-only value.

Serial Number

Set during
manufacturing.

Read-only value.

Enterprise URL

If required, enter back
office URL for remote
services back office.

Need to change
only if back office
server changes, or
if NOT using DNS.

Enterprise Tunnel URL

If required, enter back
office tunnel URL remote
services back office.

Need to change
only if back office
server changes, or
if NOT using DNS.

«
...
79
80
81
82
83
...
»

Summary of Contents for ApexPro











































































































































































































Reviews:

No comments

Related manuals for ApexPro

Brand: Gardner Bender Pages: 8

Brand: NARIKA Pages: 2

Brand: Taylor-Wharton Pages: 25

Brand: i-CAT Pages: 96

Brand: Vari Lite Pages: 14

Brand: Vaniman Pages: 3

Brand: XanLite Pages: 4

Brand: Vaillant Pages: 76

Brand: H2flow Pages: 2

Brand: V-TAC Pages: 27

Brand: Yacht Sentinel Pages: 32

Brand: X-FLOC Pages: 35

Brand: CombiSteel Pages: 60

Brand: Lightolier Pages: 2

Brand: Numark Pages: 11

AURO SPOT CLAS100

Brand: Cameo Pages: 60

Brand: Enerpac Pages: 12

Brand: Master Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands