GE Adora DFE29JG Technical Service Manual Download Page 84

Page: 84 / 91

– 84 –

Display

Mode

Comments

Dispenser Self-Test Mode

Turns on all LEDs and 7 Segments on Dispenser Board

COM Version

Return the COM Version (Only on LCD Models)

Degrees C Mode

Changes the System to be Degrees C

Degrees F Mode

Changes the System to be Degrees F

Join Zigbee Network

See Zigbee Network

Leave Zigbee Network

Get Zigbee Network Status

Force FF and FZ Defrost

Starts a FF and FZ Defrost

Exits all Defrost

Forces the Heated Defrost to the Idle State.

EXIT SERVICE MODE

Resets all boards in the system

Door Board Version Test

Con

rm UI Communication this Board

Dispenser Version Test

Deli Pan Version Test

Internal Temp Version Test

Zigbee Module Version Test

AutoFill Version Test

Main Board Version Test

FF 1 Thermistor Test

Displays Un

ltered Thermistor Temperature (display of

300 or -41 indicates open/shorted or not present)

FF 2 Thermistor Test

FF Evaporator Thermistor Test

FZ Cabinet Thermistor Test

FZ Evaporator Thermistor Test

Ambient Temp Test

Deli Pan Thermistor Test

FZ Ice Mold Body Thermistor

Test

Conv Drawer Thermistor Test

FF Door Ice Mold Body

Thermistor Test

FF Door Ice Cabinet

Thermistor Test

Hot Water 1 Thermistor Test

Hot Water 2 Thermistor Test

Humidity Sensor Test

Displays Current Humidity

Case (SxS) Flowmeter Test

Returns the Flow from Last Dispense for SxS

Door (BF) Flowmeter Test

Returns the Flow from Last Dispense for BF

Cycle Duct Door

Opens the Duct Door for 10 seconds and then closes it

Cycle FF Damper

Opens the Damper for 30 seconds then closes it

Cycle Conv Drawer Damper

Cycle QC/Deli Damper

Service Diagnostic Table

Note:

Tests will continue to run until another test is started.

All tests are not applicable to all models

(

Continued next page

)

Summary of Contents for Adora DFE29JG




























































































Search results

Summary of Contents for Adora DFE29JG

Reviews:

Related manuals for Adora DFE29JG

Brands by name

Popular brands

GE Adora DFE29JG, Technical Service Manual

Search results

Summary of Contents for Adora DFE29JG

Reviews:

Related manuals for Adora DFE29JG

Brands by name

Popular brands