manualshive.com logo in svg

GE Adora DFE29JG, Technical Service Manual

Share
Download
GE Adora DFE29JG Technical Service Manual Download Page 44

– 44 –

(

Continued next page

)

Each LED is attached to the bracket with 2 tabs. 

Freezer Compartment LEDs

The LEDs are attached onto the inside of a bracket 
located in the bottom of the LEFT fresh food door. 
The bracket is attached with a T-20 Torx screw.

Bracket

Tab

Tab

2-pin Connector

Freezer Compartment Light Switch

Freezer compartment LED switch is located on 
the right-side wall and is actuated by the strike 
attached to the right-side drawer bracket. 

Switch Strike

Light Switch

Fresh Food Compartment LEDs

To remove the LED, using a small 

fl

 at blade 

screwdriver, pry out the LED from the back side and 
slide the LED to the rear to release the tab located 
at the front. 

2-pin Connector

Front Tab

Note:

 GE/Adora models have a single LED attached 

to the bracket. The identical wiring harness is used 
on both Pro

fi

 le and GE/Adora models. A jumper is 

used on the 2nd connector to complete the circuit.

GE/Adora 

Jumper

Summary of Contents for Adora DFE29JG




























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands