GE Adora DFE29JG Technical Service Manual Download

Page: 81 / 91

– 81 –

4. Grasp the mullion and pull it vertically upward

to release it from the top and bottom retainers.

Circuit Boards

Main Control Board

The main control board operates some or all of

the following outputs, depending on the model
identi

cation used:

• Freezer temperature control using compressor,

fans and 3-way valve

• Fresh Food temperature control using

compressor, fans, 3-way valve, and damper
(single evaporator models)

• Ice Box temperature control

• Deli pan control using the damper, fan and

heater

• Variable fan speed control with RPM feedback

for the condenser, fresh food and freezer
evaporator, ice box and deli pan fans

• Freezer and fresh food evaporator defrost

control

• Icemaker control for models with an icemaker in

the freezer

• Control of freezer icemaker water valve.

• Control of case water dispenser on non-

dispenser models

• Control of the isolation water valve

• Control of mullion and ice port heaters based on

external temperature and relative humidity

• Control of the

ll tube heater for the icemaker

located in the freezer

• Control of the interior LED lighting in the fresh

food compartment

The main control board is installed in a recess

located in the back of the refrigerator. The recess
is concealed by a cover that is attached with two

1/4-in. hex head screws at the bottom and 2 tabs at

the top.

(

Continued next page

)

Summary of Contents for Adora DFE29JG




























































































Search results

Summary of Contents for Adora DFE29JG

Reviews:

Related manuals for Adora DFE29JG

Brands by name

Popular brands

GE Adora DFE29JG, Technical Service Manual

Search results

Summary of Contents for Adora DFE29JG

Reviews:

Related manuals for Adora DFE29JG

Brands by name

Popular brands