GE Adora DFE29JG Technical Service Manual Download Page 74

Page: 74 / 91

– 74 –

To remove the water fi lter on Model GE/Adora:

The water

lter, for models with icemaker in the

freezer, is located on the left side of the fresh food
compartment.

1. Pull

the

lter compartment door forward then

swing open the cover.

Note:

• A bypass cartridge is installed in the water

lter

manifold for shipping.

• The

water

lter should be installed when the

refrigerator is delivered to the consumer.

2. Grasp and pivot the water

lter out until it stops.

3. Maintaining that same angle, pull the water

lter

straight out. DO NOT TWIST OR TURN THE FILTER.

Filter Compartment

Door

Water Filter

Water Filter

The water

lter for Model PFE29 is located on the

right side of the left fresh food door.

To remove the water fi lter on Model PFE29:

Note:

Removing the water

lter turns off the water

to the door water valve.

1. Press the bottom of the

lter compartment

cover to release and swing open the cover.

Note:

• A bypass cartridge is installed in the water

lter

manifold for shipping.

• The

water

lter should be installed when the

refrigerator is delivered to the consumer.

2. Lift and pivot the water

lter upward until it

stops.

3. Maintaining that same angle, pull the water

lter

straight out. DO NOT TWIST OR TURN THE FILTER.

Filter Compartment

Door

Water Filter

Summary of Contents for Adora DFE29JG




























































































Search results

Summary of Contents for Adora DFE29JG

Reviews:

Related manuals for Adora DFE29JG

Brands by name

Popular brands

GE Adora DFE29JG, Technical Service Manual

Search results

Summary of Contents for Adora DFE29JG

Reviews:

Related manuals for Adora DFE29JG

Brands by name

Popular brands