GCC Technologies P3-60 Page 25 User Manual Download

Page: 25 / 179

Puma III User Manual

Installation 2-14

2.6.1.1 Connecting your GCC cutter

1. Turn on the machine.

2. Connect the USB connector to the machine and then USB driver will

installed automatically. It will take a few minutes to find the device. Please

DO NOT disconnect the USB cable until the installation has completed.

3. You can double click the USB icon on the taskbar to make sure the USB

device is detected.

2.6.1.2 Installing the driver

Use the USB One-click Installation for quick driver installation. Follow the

simple steps below for driver setup.

Step 1

Put the installation DVD into your CD-ROM.

Please make sure that

the USB device is connected before you start the driver

installation.

Step 2

Choose the model you want to install from the driver list and click on

Windows Driver (Win 7 and Above) (Automatic Detection) or

Windows Driver (Win 7 and Above) (Manual Selection) to start

installing the Driver and AAS plug-in.

Caution!!



If you are using Windows 7 and above as your operating system,

make sure you log in using the “Administrator” account.

Summary of Contents for P3-60




















































































































































































Search results

Summary of Contents for P3-60

Reviews:

Related manuals for P3-60

Brands by name

Popular brands

GCC Technologies P3-60, User Manual

Search results

Summary of Contents for P3-60

Reviews:

Related manuals for P3-60

Brands by name

Popular brands