GCC Technologies P3-60 Page 145 User Manual Download

Page: 145 / 179

Puma III User Manual

SignPal 12 Instruction A-6

SignPal 12 Instruction

The SignPal 12 Software is Windows System compatible and all versions support the AAS
II contour cutting function.

SignPal 12 Instruction Index:

[1] Installing the SignPal 12 software
[2] Set up your GCC Cutter on Production Manager
[3] SignPal AAS II Quick Start
[4] SignPal 12 Features List

[1] Installing the SignPal 12 software

To install the software, you must have Administrator privileges. To use the software, you
must have Administrator or Power User privileges. See your Windows user guide for more
information.

1. Uninstall any previous version of the software.

2. Go to GCC Club (

http://gccf.gcc.com.tw/gccclub/login.aspx

) and login, and select

Drivers > Cutter > Others > SignPal 12

to download the WinRAR file.

3. Follow the installation and activation instruction for SignPal 12 below.

Summary of Contents for P3-60




















































































































































































Search results

Summary of Contents for P3-60

Reviews:

Related manuals for P3-60

Brands by name

Popular brands

GCC Technologies P3-60, User Manual

Search results

Summary of Contents for P3-60

Reviews:

Related manuals for P3-60

Brands by name

Popular brands