12
13
KNOWING YOUR NEW TEA & MORE
PROPERTIES OF YOUR TEA & MORE
Your new Design Tea & More Advanced is intended for heating up drinking water
to a selectable temperature in the range between 40°C to the boiling temperature
(100°C). Depending on the currently running program, in the extreme case the
selected temperature can be maintained for several hours. For some programs, a
keep warm mode is provided.
Several programs for preparing tea or for cooking and heating up food in the pro-
vided glass insert are available. When connected to the power supply and after
completion of the selected program, the appliance will enter standby mode. Addi-
tionally, when in standby mode, without any entries for more than 5 minutes, the
appliance will shut-off automatically, to avoid useless power consumption However,
you should not leave the appliance connected to the power supply uselessly. Addi-
tionally, you should not leave the appliance operate in keep warm mode uselessly.
To avoid excessive energy loss, you may cancel any operating cycle at any time you
like by holding the “Start/Stop” button pressed for approx. 3 seconds.
During operation, only the “Start/Stop” button and “°C/Time” button are active (see
below: ‘Functions, Display and Acoustic Signals’). Any other operating elements are
idle. If you wish to make new entries, cancel the running program.
Important:
For operation, always close the kettle using the appropriate lid set (lid
ring and lid). With the lid open, the temperature control and automatic shut-off will
not work properly and there will be high energy loss.
Depending on the water hardness of your drinking water, the appliance needs regu-
lar de-scaling (see: ‘Care and Cleaning’). Otherwise, the temperature control will
not work properly, there will be an increasing energy loss, and overheating of the
heating elements could occur.
Important:
When using the cooking programs “Boil” or “Custom” with high tem-
perature settings and long cooking times, please check the filling level regularly,
because large amounts of water within the kettle could be vaporized during ope-
ration, leading to a considerable high drop in the filling level. The filling level may
not go down below the MIN filling level (500 ml), to avoid overheating. Thus,
keep the filling level under supervision during operation. If required, you can add
the appropriate amount of water without cancelling the running program (see:
‘Adding Water during Operation’).
Note
If the appliance is idle for more than 5 minutes, the appliance will shut off com-
pletely and the display gets dark for saving energy. You may reactivate the appli-
ance at any time by simply pressing any button.
3
2
4
5
6
8
15
14
1
7
10
11
12
13
1| Tea filter lid
and tea
filter lid ring
– for ope-
ration with the tea filter.
2| Tea filter:
fill with your ingredients for tea and
place it into the glass kettle.
3| Glass insert lid
and
glass insert lid ring:
use
this lid set in combination with the glass insert.
4| Glass lid:
for closing the glass insert during ope-
ration.
5| Glass insert:
for cooking and warming various
dishes and ingredients.
6| Glass kettle
made from special-purpose glass
with stainless steel heating plate.
7| Thermal insulated handle
8| Power base
with cord storage at the bottom –
holding the operating elements.
9| Power socket:
for automatically connecting the
kettle to the power supply, when the kettle is placed
onto the power base.
10| “°C/Time” button and dial:
press the cen-
tral button to toggle between the parameters. Turn
the outer dial for selecting the desired value.
11| “Start/Stop” button:
press here to start or
cancel operation.
12| “Tea” button:
for selecting the appropriate
tea program.
13| “Hot water/Cooking” button:
for selecting
the desired cooking program.
14| Display
15| Drip tray:
after cooking, place the glass insert
or tea filter here to keep your table clean and dry.
DISPLAY
Tea programs
– press the “Tea” button until the
desired program is shown
Temperature or time duration:
select the desired
parameter via the “°C/Time” button.
Cooking programs
– press the “Hot water/Coo-
king” button for selection.
Program phase:
showing the current stage of ope-
ration.
