30
31
11. After usage, you should discard the water within the kettle to avoid excessive
build-up of scale on the heating plate. Unplug the appliance.
WARMING BABY FOOD
The appliance provides a program for warming up baby food and meals for people,
who are sick and in need of care. The program “Baby” will heat 150 ml to 170 ml
milk or approx. 190 g mash in the glass insert. The water in the kettle is heated to
55°C. If you wish to warm up a larger amount of food, in most cases you can lea-
ve your food for a somewhat longer time within the appliance. However, for stirring
you should keep a suitable plastic spoon at hand when warming up mash. Do not
use any metal cooking utensils to avoid damage to the glass insert.
Note
The “Baby” program is adapted to refrigerated food with a start temperature of
approx. 4-5°C. If your food is up to room temperature already, you should take
out your food somewhat earlier.
WARNING:
The “Baby” program only warms up food. Your food will not be
cooked and thus not be sterilized in any way. At any stage of food preparation
you should ensure to prevent harmful germs from getting into the food. Purchased
ready-to-eat baby food will meet these essential requirements, if the glass has still
been closed airtight directly before warming up.
Additionally, do not use wooden cooking utensils. Even after thorough cleaning,
germs could still remain on the rough surface of wood, thus getting in your food.
It is much better to use heat-resistant plastic cooking utensils with smooth surface.
Always sterilize your cooking utensils, the glass lid, and the glass insert via boiling
water directly before use.
1. Ensure that glass insert and glass lid are clean and undamaged. There may be
no cracks and chipped edges. Sterilize the glass parts and the cooking utensils
via hot water before filling in your food.
2. Fill approx. 1 litre of clear tap water into the kettle and place the kettle onto the
power base.
3. Fill the food into the glass insert and close the glass insert via the glass lid.
4. Place the glass insert lid ring (large opening), onto the workspace and place the
glass insert into the central opening of the lid ring.
5. Then lift the lid ring at both handles. With the glass insert hanging in the lid ring,
slowly lower the glass insert into the kettle until the lid ring rests on the rim of the
kettle. Close the opening of the lid ring via the appropriate stainless steel lid.
6. Press the “Hot water/Cooking” button repeatedly until “Baby” is shown at the
lowest line of the display. The pre-defined operating time of 2½ minutes is indi-
cated on the display (“2m30s”). There is no need for any further entry.
7. Press the “Start/Stop” button to start the program. When warming up mash, you
should stir the food within the glass insert several times to get an even result.
When the pre-set water temperature in the kettle (55°C) is reached, the war-
ming up time (“Steeping”) starts, displayed as a count-down. After 2½ minutes
a signal sounds and the display shows “End”.
8. Check the temperature of your food. If the food has not reached the desired
temperature, just leave the glass insert within the kettle. For your assistance, after
each 40 seconds, a beep will sound.
Tip:
To keep your workspace dry, you should keep the provided stainless steel
bowl or another sufficient coaster for placing the glass insert on it.
9. Grasp the lid ring at both handles and lift the lid ring including the glass insert
out of the kettle. Carefully place the glass insert on the stainless steel bowl or
coaster and lay down the lid ring. Now you can grasp the glass insert easily
for taking out your food.
Important:
Before feeding, always check the temperature of the food.
10. Stir the food and check the temperature before feeding.
Note
The water within the kettle will stay warm for some time after heating. If you wish
to keep your food warm, simply place the glass insert back into the kettle.
11. After usage, cancel the program by holding the “Start/Stop” button pressed for
3 seconds.
12. You should discard the water within the kettle to avoid excessive build-up of
scale on the heating plate. Unplug the appliance.
RESETTING TO FACTORY SETTINGS
When making your individual changes to the pre-programmed settings of the
“Custom” program, the appliance will keep your settings in memory—even after shut
off and disconnecting the appliance from the mains power supply. However, you
may wish to restore the pre-programmed factory settings. For this, proceed accor-
ding to the following steps.
