24
25
3. Replace the glass insert in the kettle by holding the glass insert with the handles
of the glass insert lid ring. The kettle will heat the water up to the set temperature
and carry on executing the running program as normal.
COOKING MEALS WITHIN THE KETTLE – “BOIL” AND “CUSTOM”
Various meals can be cooked within the tea kettle (see: ‘Recipes’). For this, it is best to use
the cooking programs “Boil” or “Custom”. When putting your own ideas into practice,
please keep in mind that the temperature within the glass insert will be slightly below the
set temperature within the kettle. The higher the set temperature, the higher the difference
will be. Additionally, the difference will depend on the amount of water within the kettle
and the amount of food within the glass insert. To keep the difference as low as possible,
you should always use the glass lid and the stainless steel lid of the glass insert lid set.
Note
You should adapt the filling level in the kettle to the amount of food you wish to
cook/heat in the glass insert. With only a small amount of food in the glass insert,
you should reduce the maximum amount of water in the kettle to 700 - 800 ml.
WARNING:
Before each use, always ensure that the glass insert and glass
lid are undamaged. There may be no cracks or chipped edges. When taking the
glass insert out of the kettle after cooking, please keep in mind that the glass insert
could be hot and hot condensate and steam could escape, depending on the set
temperature. If required, use pot holders or rubber gloves to protect your hands.
Do not place the hot glass insert on any surfaces sensitive to heat and moisture.
Note
The cooking program “Custom” will heat the water within the kettle up to the indi-
vidually adjustable temperature from 40°C to 100°C. With the “Boil” program
the temperature is set to 100°C automatically,and the water will be heated up to
the boil first. Thereafter the selected cooking time (“Steeping”) will start and the
appliance will keep the water at the set temperature. However, the maximum tem-
perature during cooking time is limited to 90 - 95°C to avoid too high loss of water
due to evaporation. After the cooking time elapsed, a signal sounds and the keep
warm function (“Warm”) is started, running for up to 60 minutes. With the keep
warm function, the temperature in the kettle is limited to 80°C at the maximum.
Tip:
If you wish to use special temperature settings or elongated cooking times, use
the “Custom” program (see: ‘Properties of Your Tea & More/Cooking Programs”).
Important:
Please keep in mind, that the water within the kettle will vaporize gra-
dually, when kept at high temperature for an elongated time. Thus, check the filling
level at least every 15 - 20 minutes, when using the cooking programs at high tem-
perature settings. The filling level may not fall below the MIN filling level (500 ml).
If required, add some water to the kettle (see: ‘Adding Water during Operation’).
USING THE “BOIL” PROGRAM
1. Ensure that glass insert and glass lid are clean and undamaged. There may be
no cracks and chipped edges. If required, sterilize the glass parts via hot water
before filling in your food.
2. Fill 500 ml to 1100 ml of clear tap water into the kettle and place the kettle onto
the power base.
3. Fill the prepared food into the glass insert. However, do not fill in more than
480 ml. Then close the glass insert via the glass lid.
4. Place the glass insert lid ring (large opening) onto the work space and place the
glass insert into the central opening of the lid ring.
5. Then lift the lid ring by both handles. With the glass insert hanging in the lid
ring, slowly lower the glass insert into the kettle until the lid ring rests on the rim
of the kettle. Close the opening of the lid ring via the large stainless steel lid of
the glass insert lid set.
6. Press the “Hot water/Cooking” button repeatedly until “Boil” is indicated at the
lowest line of the display.
7. Set the cooking time by turning the “°C/Time” knob until the required value is shown.
Note
With the “Boil” program, you can only set the cooking time in the range of 0 to
30 minutes (“30m00s”). The temperature setting is fixed. If you wish to use another
temperature, use the completely programmable “Custom” program.
After the program is started, using the “°C/Time” button, you can toggle the para-
meters shown on the display as you like. After 6 seconds without any actions, the
appliance will switch back to the usually displayed parameter.
8. Press the “Start/Stop” button to start the program. The appliance will heat the
water within the kettle immediately. As soon as the boiling temperature is reached,
the count-down timer of the cooking time (“Steeping”) starts. However, during the
cooking time the kettle reduces the temperature to 90-95°C. At the end of the set
cooking time, a signal sounds and will be repeated once after 40 seconds. The
