![background image](http://html1.mh-extra.com/html/garland/xg36/xg36_installation-and-operation-manual_3768848006.webp)
Part # 4517124 Rev. 7 (08/17/11)
Page 6
SAFETY PRECAUTIONS
Always follow these safety precautions when operating the
Xpress Grill.
• THIS GRILL MUST
be operated by persons who have
been given adequate training.
• THIS EQUIPMENT MUST ONLY BE OPERATED UNDER AN
APPROVED HOOD SYSTEM.
• DO NOT
operate the grill without reading this operation
manual.
• DO NOT
operate the Xpress grill unless all service and
access panels are in place and fastened properly.
The Garland Xpress Grill is a semi-automatic cooking
appliance. The upper platen is lowered automatically,
following the manual, two-handed initiation of the cooking
cycle, and the upper platen is raised automatically upon
completion of the cooking cycle.
When two sided cooking, the area between the upper platen
and the griddle plate should be regarded as a “danger zone.”
During two sided cooking the operator must not be within
this danger zone. When used as a flat grill, then this area is no
longer a danger zone, the platens do not move.
For whatever reason, be it cleaning, maintenance, or normal
operation, any exposed person must use extreme caution if
within this danger zone.
In two side cooking the upper platen remains in the lowered
position by nature of its own weight. It is not locked down. It
can be raised by lifting up on the handle on the front of the
platen.
The Xpress Grill may during its operation emit airborne noise
equivalent to a continuous A weighted sound pressure level
of 73dB(A).
WARNING: To avoid serious personal injury:
• DO NOT
attempt to repair or replace any part of the
Xpress Grill unless all main power supplies to the grill
have been disconnected.
• USE EXTREME CAUTION
in setting up, operating and
cleaning the Xpress Grill to avoid coming in contact
with hot grill surfaces or hot grease. Suitable protective
clothing should be worn to prevent the risk of burns.
• DO NOT
clean this appliance with a water jet.
• DO NOT
apply ICE or COLD WATER to a HOT grill surface.
•
NOTE all warning labels and markings affixed to the grill.
WARNING:
After turning the master power switch to the
START position, the grill will go through initialization. If
the upper platens are in the lowered position they will
return to their raised upper position. This movement takes
approximately 8 seconds.
INSTALLATION
IMPORTANT: Rating plate for this appliance is located on
the right side panel.
This equipment must be installed by a competent factory
trained, certified, licensed and / or authorized service or
installation person.
WARNING:
This appliance must be properly grounded.
Prior to installation, the four casters, supplied loose with the
grill, must be securely located on the underside of the base.
The casters fitted with a brake must be located at the front of
the grill.
This appliance should be connected to a potential
equalization system. A labeled equipotential bonding point
is fitted to the rear of the grill.
It is recommended that this grill be connected to a residual
current,, (earth leakage),, device with a tripping current not
exceeding 30mA. The leakage current of this grill will not
exceed 5mA.
CAUTION:
Prior to installation, check the electrical supply
to ensure input voltage and phase match the equipment
voltage rating and phase. See data plate located rear left side
of grill and lower front panel.
Summary of Contents for XG36
