Garland MWE1S Page 18 Installation, Operation & Service Manual Download

Page: 18 / 94

INSTALLATION/OPERATION & SERVICE MANUAL - 1&2 PLATEN

GARLAND CLAMSHELL GRILLS WITH PRODUCT RECOGNITION

PART #4527466 (12 Aug 2011)

Page 18

INSTALLATION & STARTUP

(continued)

POWER SUPPLY CONNECTION:

All electric connections must be made by a qualifi ed,
properly equipped technician.

NOTE: WIRING DIAGRAM LOCATED INSIDE

LOWER FRONT PANEL.

“DISCONNECT POWER BEFORE OPENING”

RECOMMENDED PLUG

MWG2W = 1X NEMA 15-30

MWE2W = 2X NEMA 15-50

MWG2W

HAS ONE ELECTRICAL CORD.

MWE2W

HAS TWO ELECTRICAL CORDS.

POWER CORDS & PLUGS

ARE NOT SUPPLIED

BY THE MANUFACTURER

RECOMMENDED PLUG

MWG2W

= 1X NEMA 15-30

MWE2W

= INSTALL LINE SIDE

MIN. #8AWG “JUMPERS”

INPUT 1 to INPUT 2

1X NEMA 15-60

Electrical Cable Hookup

SINGLE POWER SUPPLY CONNECTION

where required by local regulations

Electrical Cable Hookup

DUAL POWER SUPPLY CONNECTION

USA & some other

POWER CORDS & PLUGS

ARE NOT SUPPLIED

BY THE MANUFACTURER

INPUT 1

INPUT 2

INPUT 1

INPUT 2

1 x 20AMP NEMA 21-20

Ora Red Blk

Wht

t Wht Wht

Ora Red Blk

Wht Wht Wht

POWER CORDS

ARE NOT SUPPLIED

BY THE

MANUFACTURER

Hood-Interlock & Control Power Supply; where applicable

5. Install Front Gas connection: Isolate grill from any

power source by unplugging all electrical connections.

A. Rotate existing elbow as shown in the diagrams

below.

B. Attach support bracket (PN 4528775)to base

as shown with #10-24 screws and lock washers
supplied.

NOTE: For retrofi t applications, drill 2x .161 holes and
use self tapping screws provided.

C. Install 3/4” NPT nipple through support bracket and

onto existing elbow. Attach locking ring with 2x
#10-24 screws.

D. Install connector 3 inches long (Used on single

platen Only)

E. Install elbow to orientation show below.

F. Install

nipple.

G. Attach fl ex gas hose to nipple.

6. Install shut off sticker as shown above to bottom of

front control panel.

12 REF

1.75 REF

6.00

1.500

9.0

30°

INSTALL ELBOW #1026715 TO

ORIENTATION SHOWN

7. GAS GRILL ONLY,

(for electric grills, skip to step 8 ):

Install the included quick-disconnect gas hose to the
inlet fi tting on the underside of the grill by threading
brass male quick-connect coupler included with the
hose onto the factory-installed elbow.

MALE COUPLER
[INSTALL FIRST]

TO GAS
SUPPLY

FACTORY

INSTALLED

GAS INLET

UNDERNEATH GRILL

FLEXIBLE GAS HOSE

GAS
FLOW

Summary of Contents for MWE1S































































































Search results

Summary of Contents for MWE1S

Reviews:

Related manuals for MWE1S

Brands by name

Popular brands

Garland MWE1S, Installation, Operation & Service Manual

Search results

Summary of Contents for MWE1S

Reviews:

Related manuals for MWE1S

Brands by name

Popular brands