Garland MWE1S Page 19 Installation, Operation & Service Manual Download | Manualshive

Page: 19 / 94

background image

GARLAND CLAMSHELL GRILLS WITH PRODUCT RECOGNITION

INSTALLATION/OPERATION & SERVICE MANUAL - 1&2 PLATEN

PART #4527466 (12 Aug 2011)

Page 19

INSTALLATION & STARTUP

(continued)

Connect the hose and ensure the sleeve snaps fully
forward against the retaining ring.

With the manual shut-off valve closed, install the
other end of the hose to the gas supply. If the grill
is equipped with an optional front gas connection,
see the sub-section titled, “Front Gas Connection” on
the following page for dimensions and positioning
information.

8. Install

fl ue box to back of grill for single or double

platen (If required).

FLUE BOX CLIPS ON REAR LIP OF

GRILL & IS CENTERED SIDE TO SIDE

FLUE BOX IS NOT SUPPLIED

BY THE MANUFACTURER

FOR GAS GRILLS ONLY

9. Install grease bucket rails as shown below:

ATTACH SHUT-OFF

STICKER IN THIS

LOCATION

.750

RAIL

GREASE BUCKET

GREASE BUCKETS & RAILS NOT

SUPPLIED BY MANUFACTURER

10. Roll grill under hood. Grill must be level front to back,

side to side and diagonally. Adjust casters accordingly
to obtain fi nal level.

Hood Type & Platen Height

With the platens in the raised position, measure the height
from the front edge of the platen to the grill surface. If the
platen height is over 17” (431mm), it must be adjusted to
proper clearance by an authorized service agent.

45°

17in

[431

mm

]

MAX

LonWorks Information & Commissioning
To Activate the grill onto the Lonworks
network:

To enable the power line communications between the
grill and the Lonworks network the grill must fi rst be
commissioned onto the network.

«
...
17
18
19
20
21
...
»

Summary of Contents for MWE1S































































































Reviews:

No comments

Related manuals for MWE1S

Brand: Makerfire Pages: 10

Brand: PANDROL Pages: 36

Brand: R&S Pages: 2677

Brand: Lalizas Pages: 12

BOBCAT 130 Series

Brand: Balcrank Pages: 12

Ti-Lite Carbo AirBlock 351

Brand: Harken Pages: 2

KONTROL KUBE ABACUS

Brand: FIBERLOCK Pages: 8

Brand: Monosem Pages: 92

Brand: Otto Bock Pages: 252

Brand: ResMed Pages: 8

Brand: Microsport Pages: 7

Brand: BPW Pages: 4

AKKU BEK-10 Kaleidoscope

Brand: EuroLite Pages: 16

Brand: KaVo Pages: 24

Brand: Facnor Pages: 4

IEC cartridge alignment gauge

Brand: Clearaudio Pages: 8

Ergociser EC-5000

Brand: Cateye Pages: 64

Brand: Pari Pages: 318

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands