manualshive.com logo in svg

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER, Installation & Programming Instructions, Page: 7 / 38

Share
Download
GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions Download Page 7

3.1

CONNECTION TO GARDTEC 

800 Series & 580

Connection to the Gardtec 

800 Series (or Gardtec 580  via interface) is via the Speech

Dialler Serial Lead Part No 04-070. The plug end of the lead should be connected to the
Gardtec 

800 Series  SK3 (Digigard Communicator) (or PLG1 on the 580  interface) the

flying end should be connected to the dialler as shown below.

Dialler

Flying Lead

Function

Terminal

Core Colour

Panel  to Dialler      

FLT

Yellow

DIN to DOUT

TRG1

Green

DOUT to DIN

TRG2

Black

CLOCK

0V

Blue

0V

12V

Red

12V

Program Gardtec 

800  Digicom Type option to Digigard.

Program Gardtec 

800  PA Mode to Bells Always or Silent

When the Speech Dialler is connected to the Gardtec 

800  Alarm activation will trigger

message 3, PA activation will trigger message 2 and channel 1 activation (as
programmed) will trigger message 1.
The link between 12V and  Line fault on the Gardtec 

800  must be removed.

3.2

CONNECTION TO OTHER EQUIPMENT

The dialler may be connected to any equipment that is able to give a positive or negative
output examples of this are given in Figs 2 to 5.

Fig 2.

1

2

3

4

5

6

7

8

NO

9

0

YES

FLT   TRG1 TRG2 TRG3   TMP   TMP     0V     12V

To L/F

Input

To Control

Panel

Tamper Loop

To Control
Panel 12V

Aux Supply

Fire       PA

Alarm

Control Panel Outputs

PR4100Rev1.7 SD.QXD  07/03/01  16:22  Page 7

Summary of Contents for GARDTEC SPEECH DIALLER







































Reviews:

No comments