background image

1.0

INTRODUCTION

The Gardiner Technology Gardtec Speech Dialler is intended for use as an automatic
message dialler. The primary use for the dialler is for connection to an alarm system
although the unit is flexible enough to have many other uses where the need for automatic
messages exists.

The dialler is fully programmable via an engineer code with limited programmable options
available to the user via a user code. Once programmed the unit will retain all
programmed settings (including speech), even in the event of a complete power down.

Up to four telephone numbers may be programmed into the dialler and call
acknowledgment may be programmed on or off

The unit may be used with the Gardtec 800 Series of control panels (or Gardtec 580 via an
interface) as a plug on unit, or hardwired to any other control panel that offers suitable
outputs. 

The dialler offers one common message (11 seconds duration) and up to three shorter
messages (3 seconds duration each). 

When connected to the Gardtec 800 Series or the Gardtec 580 (with interface) the dialler
is powered and activated via the serial communications link to the control panel. If
connected to other control equipment the dialler should be given a 12V d.c supply and is
triggered via three start input terminals, the start polarity of these terminals is fully
programmable.

Once triggered the dialler will dial the first telephone number, when the call is answered
the common message will be played followed by one of the three short messages
corresponding to alarm channels 1, 2 and 3 on the Gardtec (or inputs 1, 2 or 3 if controlled
by other equipment). If acknowledge is programmed off the dialler will terminate the call
after passing the message to the first telephone number , if no answer is obtained from
telephone number 1 the unit will sequentially move on to the next telephone numbers until
it is successful. 

If acknowledge is programmed to on, the unit will dial the telephone numbers in the same
way but the calls will require acknowledgement by the call recipient. The number of
acknowledged calls require to terminate the dialling sequence is fully programmable by the
user.

PR4100Rev1.7 SD.QXD  07/03/01  16:22  Page 4

Summary of Contents for GARDTEC SPEECH DIALLER







































Reviews: