manualshive.com logo in svg

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER, Installation & Programming Instructions, Page: 23 / 38

Share
Download
GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions Download Page 23

For positive trigger with internal pull-down resistors.

For negative trigger with internal pull-up resistors
switched out.

When you are satisfied with the Trigger Mode shown 
press YES and the dialler will return to step 1.

3)

Pressing 0 once will return to the 'P' display or twice will 
return to the 'on' or 'oF' state.

Note:

No access will be allowed to this section if serial comms mode is 
programmed to ON

7.9

PROGRAMMING LINEFAULT MONITOR

No access is available to this option via the user code, it may only be accessed via
the engineer code.

Enter the engineers Menu (refer to section 7.0)

1)

With the display showing:-

2)

Enter 4. If NO is pressed the current Linefault Monitor 
voltage will be displayed and the dialler will return
to step 1.

or

If YES is pressed the current Linefault Monitor will be 
displayed. Press NO to change the Linefault Monitor to 
one of the following:-

4 volt monitor for lines sharing with other equipment.

PR4100Rev1.7 SD.QXD  07/03/01  16:22  Page 23

Summary of Contents for GARDTEC SPEECH DIALLER







































Reviews:

No comments