GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions Download Page 15 | Manualshive

Page: 15 / 38

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions Download Page 15

6.0

INITIAL POWER UP

The dialler is supplied from the factory with a set of defaults pre-loaded, these defaults will
be adequate for the majority of installations with the exception of at least one telephone
number, and at least one common and alarm message.

When the unit is first powered up the display will show:-

For the first eight seconds.

If the dialler has previously been programmed, one of the factory
default reset modes may be used (see engineers appendix 2).

When the eight seconds has expired the display will show:-

For up to one minute.
During this period the dialler is running a self calibration routine

After the calibration routine has finished the display will show
one of the following:-

The 'on' display shows the unit is turned on and is ready for
a trigger, the 'oF' display shows the unit is turned off.
If the 'oF' display is flashing the unit needs to be programmed
with at least one telephone number and one common and
alarm message.

PR4100Rev1.7 SD.QXD 07/03/01 16:22 Page 15

«
...
13
14
15
16
17
...
»

Summary of Contents for GARDTEC SPEECH DIALLER







































Reviews:

No comments