manualshive.com logo in svg

GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER, Installation & Programming Instructions, Page: 29 / 38

Share
Download
GARDINER TECHNOLOGY GARDTEC SPEECH DIALLER Installation & Programming Instructions Download Page 29

Call Abort
The last call was aborted by the user, this message would 
only be seen by viewing the last call log

Abort
The current dialling sequence has been aborted (e.g the user 
or engineer code has been entered).

Line Fault
A Line Fault has occurred, the display will return to normal 
when the line is reinstated.

Fail to Speak
The dialler has failed to pass the speech message(s), this may 
be due to a line fault being present as the dialler was attempting 
to dial. The display may be cleared by either a successful 
communication or entering the user code (dependant on the status 
of the FTC (FS) clear by user code option 

see 7.12 ).

Alarm
The call was aborted after the message had started to play. 
The last call log may be used to determine who the called 
person was.

Low Power
Voltage to the dialler has fallen to 9.5V or lower

PR4100Rev1.7 SD.QXD  07/03/01  16:22  Page 29

Summary of Contents for GARDTEC SPEECH DIALLER







































Reviews:

No comments