Gamma DIGITEL MPCq User Manual Download Page 26

Page 26 of 28

Gamma Vacuum DIGITEL MPCq Users Manual

Document 900034, Rev B

18. WARRANTY & SERVICE

18.1 Service

Cleaning Procedure

Prior to any cleaning of the controller, the mains power should be 
disconnected. Once powered off, use a 50% distilled water and 
50% isopropyl alcohol solution to clean the entire unit. A soft, non 
abrasive cloth will ensure no damage to the LCD screen and finish of 
the unit.

Service Requests

Service requests should go through customer center or local sales 
representative originally purchased through.
Upon notification, Gamma Vacuum or representative customer 
center will identify the level of service required. To assist in this 
process, please provide the following information in as much detail 
as possible:

• 

Part Number

• 

Serial Number

• 

Detailed Description of the Vacuum System Hardware

• 

Detailed Description of the Vacuum System Process (gas species 
introduced, ultimate pressure, operational pressure)

• 

Reason for Service Request

• 

Required Documentation

To expedite this process, please forward this information to  

[email protected]

.

Direct Support

Prior to recommending replacement parts or service at our facility, 
Gamma Vacuum can assist with general vacuum issues via e-mail 
or by telephone at no charge. It is our goal to have vacuum systems 
functional with minimal time and financial investment.
To do this, our service technicians require as much information as 
possible about the vacuum system in need of support. To assist in this 
process, please provide the following information in as much detail 
as possible:

• 

Part Number

• 

Serial Number

• 

Detailed Description of the Vacuum System Hardware

• 

Detailed Description of the Vacuum System Process (gas species 
introduced, ultimate pressure, operational pressure)

• 

Reason for Support Inquiry

To expedite this process, please forward this information to   

[email protected]

 or contact our facility directly at the 

numbers below.

18.2 Warranty

General Terms

Gamma Vacuum warrants to the Buyer that the equipment sold 
is new equipment, unless previously stated, and is, at the time of 
shipment to Buyer from Gamma Vacuum, free from defects in 
material and workmanship. As Buyer’s sole exclusive remedy under 
this warranty, Gamma Vacuum agrees to either repair or replace, at 
Gamma Vacuum’s option and free of parts charge to Buyer, and part 
or parts which, under proper and normal conditions of use, prove 
to be defective within twelve (12) months from the date of receipt by 
buyer.
As expendable items may have a life time of less than one year, their 
warranty is subject to reasonable service and will be replaced as 
determined by Gamma Vacuum. All warranty claims must be brought 
to the attention of Gamma Vacuum within thirty (30) days of failure 
to perform.
This warranty does not cover loss, damage, or defects resulting 
from transportation to the buyer’s facility, improper or inadequate 
maintenance by buyer, buyer supplied software or interfacing, 
unauthorized modifications of misuse, operation outside of 
environmental specifications for the equipment or improper site 
preparation and maintenance.
In-warranty repaired or replacement parts are warranteed only for 
the remaining unexpired portion of the original warranty period 
applicable to the parts which have been repaired or replaced. After 
expiration of the applicable warranty period, the Buyer shall be 
charged at Gamma Vacuum’s then current prices for parts, labor, 
and transportation.
Reasonable care must be used to avoid hazards. Gamma Vacuum 
expressly disclaims responsibility for any loss or damage caused 
by the use of its products other than in accordance with proper 
operating and safety procedures.
EXCEPT AS STATED HEREIN, GAMMA VACUUM MAKES NO 
WARRANTY, EXPRESSED OR IMPLIED (EITHER IN FACT OR BY 
OPERATION OF LAW), STATUTORY OR OTHERWISE: AND, 
EXCEPT AS STATED HEREIN, GAMMA VACUUM SHALL HAVE NO 
LIABILITY FOR SPECIAL OR CONSEQUENTIAL DAMAGES OF 
ANY KIND OR FROM ANY CAUSE ARISING OUT OF THE SALE, 
INSTALLATION, OR USE OF ANY OF ITS PRODUCTS.
Statements made by any person, including representatives of Gamma 
Vacuum, which are inconsistent or in conflict with the terms of this 
warranty shall not be binding upon Gamma Vacuum unless reduced 
to writing and approved by an officer of Gamma Vacuum.
Gamma Vacuum may at any time discharge its warranty as to any 
of its products by refunding the purchase price and taking back the 
products.

Summary of Contents for DIGITEL MPCq





























Reviews: