GALILEI GIANO 70, User And Maintenance Manual

Page: 42 / 48

k Cod. 80004170 – 04.04.2018
PARAMETERS TABLE
Attention
: the access to the programming menus and the modification of the parameters are
exclusively reserved to installation and maintenance personnel. A wrong or improper modification of the
parameters can lead to malfunctions and/or to a lack of performances.
Cabinet type: Giano R290
Gemini R290
Aries R290
Controller: Dixell XR50CX
Defrost: Hot gas
Release Tabella: 80004170 – 04.04.2018
Programmation Table: 80003980
Parametertabelle
Cod. Type Parameter description u.o.m. Range Def.
SET -
Set Point (valid only for stand-alone counters)
°C LS÷US
2
Hy Pr1
Differential (Hystheresis)
°C 0.1÷25.5 2
LS Pr2
Minimum Set Point
°C -50÷Set -2
US Pr2 Maximum Set Point °C Set÷110 10
ot Pr1 Thermostat sensor calibration °C -12÷12 0.0
P2P Pr1 Evaporator sensor presence - n÷Y Y
oE Pr2 Evaporator sensor calibration °C -12÷12 0
P3P Pr2 Third sensor presence - n÷Y N
o3 Pr2 Third sensor calibration °C -12÷12 0
odS Pr2 Outputs delay at startup min. 0÷255 2
AC Pr1 Min. time between Compressor Off and successive start min. 0÷50 4
rtr Pr2 P1-P2 percentage for regulation (100=P1, 0=P2) - 0÷100 80
CCt Pr2 Continuous cycle duration H 0÷24 0
CCS Pr2
Set Point for continuous cycle
°C -55÷150 4
Con Pr2
Continuous ON time with faulty sensor
min. 0÷255 10
CoF Pr2
Continuous OFF time with faulty sensor
min. 0÷255 10
CF Pr2
Temperature measurement unit
- °C÷°F °C
rES Pr1
Resolution (in=integer; de=decimal point)
- In÷de De
Lod Pr2
Probe displayed
- P1÷on on
dLy Pr2
Display temperature delay Min. 0÷20 0
dtr Pr2 with Lod=dtr, percentage of visualization betw. temp. P1 and P2 - 1÷99 99
tdf Pr1 Defrost type (El=el.heater, in=hot gas) - El÷in in
dFP Pr2 Probe selection for defrost termination (nP,P1,P2,P3,P4) - - P2
dte Pr1 Defrost termination temperature
°C -50÷50 7
idF Pr1 Interval between defrost cycles h 1÷120 4
MdF Pr1 Maximum length of defrost
min. 0÷255 30
dSd Pr2 Start defrost delay min. 0÷99 0
dFd Pr2 Displaying mode during defrost (rt, it, Set, DEF) - - SET
dAd Pr2 Max display delay after defrost min. 0÷255 0
Fdt Pr2 Draining time min. 0÷120 5
dPo Pr2
First defrost after startup (n=after idF, y=immed.)
- n÷y Y
dAF Pr2
Defrost delay after fast freezing (0÷23h 50’)
- - 0
ALC Pr2
Temperature alarm config. (rE=related to Set, Ab=absolute)
- rE÷Ab rE
ALU Pr1
Maximun temperature alarm
°C Set÷110 10
ALL Pr1
Minimum temperature alarm
°C -50÷Set 5
AFH Pr2
Differential for temperature alarm recovery
°C 0.1÷25.5 1
ALd Pr2
Temperature alarm delay
min 0÷255 15