background image

Gal Pro

 

Instruction 1.0

Number of outputs in Gal Pro 4: 9 (4 valves, master, fertilizer pump, 2 filters and alarm).

Number of outputs in Gal Pro 8: 13 (8 valves, master, fertilizer pump, 2 filters and alarm).

Number of Inputs: 8 (4 water counters, 1 fertilizer counter, 3 condition inputs).

Analog Inputs: None

Input Voltage Gal Pro DC: 6 volts (4 * 1.5 VDC Alkaline D type batteries installed inside the 
controller). Or 12 VDC battery 5 Amp * H or more connected to a charger or solar panel.

Power Consumption When Idle: 0.2 - 0.3 mA.

Type of Solenoids: 12 VDC latch - 2 or 3 wires.

Pulse Duration: 20 mS to 200mS - programmable

Dimensions:

  H - 23 cm
  L - 30  cm
  W - 13 cm

gal pro DC Weight(without Batteries): 1.75 kg 

Gal pro AC Weight (without protection cards): 2.95 kg                      

Irrigation According to: M3, Liters, Seconds, Minutes, Hours

Fertilization According to: Minutes, Liter/M3, calculated proportional including water before  
and after.

Filter Flushing: Up to 2 filters according to time, water quantity or PD switch.

Irrigation Day Definition: according to cycle days or days of the week.

Irrigation Cycles per Day:  From 1 to 255.

Diaries: Alarm and event records of irrigation activity. Up to 128 events.

Timing of Opening and Closing Valves: Full control of operation order of the master valve and 
the irrigation valves at the beginning and end of irrigation. Overlapping the valve operation in 
changing valves.

Manual Control: Full manual control of sequences and valves including control of irrigation 
outside of the program timetable.

External Conditions: 3 input conditions that enable operating, pausing, starting and stopping the 
irrigation according to condition elements with dry contacts.

Alarms: The controller displays all types of alarms during the irrigation and fertilization. It is 
possible to define automatic alarm canceling. In addition the alarm output can be connected to a 
cellular text message sender.

Saving Data: The controller saves all of the definitions and irrigation programs even when the 
power supply is disconnected. The data that are not saved are: time, date and accumulations.

13. Technical Specifications

Summary of Contents for Gal Pro 4













































Reviews: