Galaxy GHDX2-2430S-16F4D Installation And Hardware Reference Manual Download Page 92

Page: 92 / 100

Galaxy GHDX2-2430S-16F4D Installation and Hardware Reference Manual

B-6

Fault Tolerance Management

B.7. Fault Tolerance Management

Specification

Drive S.M.A.R.T Support

Yes (with user-configurable detect only, clone
and replace, and perpetual clone functions)

Battery Back-up Option

Yes

ISEMS (Simple Enclosure
Management Service) via I

Interface

Yes

Automatic Drive Failure
Detection

Yes

Automatic Rebuild on Spare
Drives

Yes

Regenerate Logical Drive Parity

Yes

Bad Block Reassignment

Yes

Automatic Rebuild upon Failed
Drive Replacement

Yes

Manual Clone of Suspected
Failed Drive

Yes

Concurrent Rebuild on Multiple
Drives in a RAID (0 + 1) Logical
Drive

Yes

Salvage the 2

Temporary Failed

Drive in a RAID 1, 3 or 5 Logical
Drive

Yes

Salvage the 1

Temporary Failed

Drive in a RAID 0 Logical Drive

Yes

Summary of Contents for GHDX2-2430S-16F4D





































































































Search results

Summary of Contents for GHDX2-2430S-16F4D

Reviews:

Related manuals for GHDX2-2430S-16F4D

Brands by name

Popular brands

Galaxy GHDX2-2430S-16F4D, Installation And Hardware Reference Manual

Search results

Summary of Contents for GHDX2-2430S-16F4D

Reviews:

Related manuals for GHDX2-2430S-16F4D

Brands by name

Popular brands