Galaxy GHDX2-2430S-16F4D Installation And Hardware Reference Manual Download Page 19

Page: 19 / 100

Galaxy GHDX2-2430S-16F4D Installation and Hardware Reference Manual

1-6

Galaxy Raid

Components

1.2.2 Drive Trays

Figure 1-7: Drive Tray

PN: GAL-9273CDTray

Each GHDX2-2430S-16F4D subsystem comes with sixteen (16) drive trays.

The front panel of each drive tray (see

Figure 1-7

) contains a locking

mechanism that secures the drive tray to the enclosure and a latch that

facilitates the removal and installation of the drive tray. Two (2) status-

indicating LEDs are also located on the front of the drive tray. Retention

screw holes are located on the sides of the drive tray. These holes are

reserved for securing hard drives to the tray. Other retention screw holes are

located on the surface of the tray at the rear.

WARNING!

Be careful not to warp, twist, or contort the drive tray in any way (e.g., by

dropping it or resting heavy objects on it). The drive tray has been

customized to fit into the drive bays in the subsystem. If the drive bay

superstructure is deformed or altered, the drive trays may not fit into the

drive bay.

1.2.3 RAID

Controller

Modules

Part Number:

GHDX2/16-2430S-FC4

Figure 1-8: Controller Module

The RAID controller module that shipped with your subsystem contains a

metal bracket, a main circuit controller board, a management rear panel, and

Summary of Contents for GHDX2-2430S-16F4D





































































































Search results

Summary of Contents for GHDX2-2430S-16F4D

Reviews:

Related manuals for GHDX2-2430S-16F4D

Brands by name

Popular brands

Galaxy GHDX2-2430S-16F4D, Installation And Hardware Reference Manual

Search results

Summary of Contents for GHDX2-2430S-16F4D

Reviews:

Related manuals for GHDX2-2430S-16F4D

Brands by name

Popular brands