Galaxy GHDX2-2430S-16F4D Installation And Hardware Reference Manual Download Page 27

Page: 27 / 100

Galaxy GHDX2-2430S-16F4D Installation and Hardware Reference Manual

1-14

Hot-swappable Components

•

PSU with cooling module

•

Optional BBU

•

Hard drive

NOTE:

Instructions on how to replace these hot-swappable components are given

in Chapter 5.

1.4.3 Normalized

Airflow

Proper subsystem cooling is referred to as “normalized” airflow.

Normalized airflow ensures the sufficient cooling of the subsystem and is

only attained when all the components are properly installed. Therefore, a

failed component should only be hot-swapped when a replacement is

available. If a failed component is removed but not replaced, permanent

damage to the subsystem can result.

Summary of Contents for GHDX2-2430S-16F4D





































































































Search results

Summary of Contents for GHDX2-2430S-16F4D

Reviews:

Related manuals for GHDX2-2430S-16F4D

Brands by name

Popular brands

Galaxy GHDX2-2430S-16F4D, Installation And Hardware Reference Manual

Search results

Summary of Contents for GHDX2-2430S-16F4D

Reviews:

Related manuals for GHDX2-2430S-16F4D

Brands by name

Popular brands