Gage Bilt GB2581WS Original Instructions Manual Download Page 21

Page: 21 / 24

7/21 REV 3/23

GB2581WS / GB2581AWS INSTALLATION TOOL.

PATENT

PENDING

STRAIGHT FEED N SWAGE

SEMI-AUTOMATIC INSTALLATION TOOL

FOR USE WITH THE GB731 HYDRAULIC INSTALLATION

TOOL OR THE GB745 HYDRAULIC INSTALLATION TOOL

WITH ADAPTER (745751)

FOR 5/32” - 3/8” LGP® 3SLC-C Collars

Contact Gage Bilt for more information

(Sold Separately)

STRAIGHT FEED N SWAGE

Approved for use on Gage Bilt CE installation tools and/or other manufacturer’s CE approved tools of similar design.

(Sold Separately)

SWAGING: EASY AS...

Operator presents nose to pintail and

feeder dispenses collar onto pin.

Feeder pivots, exposing nose for

installation, while picking up next collar.

Feeder automatically returns to original

position for next lockbolt installation.



SAFER COLLAR INSTALLATION



INCREASE PRODUCTIVITY



ELIMINATE FOD



REDUCE FASTENER COSTS



EASY FEED TUBE INSTALLATION

Images may not reflect actual tool

Summary of Contents for GB2581WS

























Search results

Summary of Contents for GB2581WS

Reviews:

Related manuals for GB2581WS

Brands by name

Popular brands

Gage Bilt GB2581WS, Original Instructions Manual

Search results

Summary of Contents for GB2581WS

Reviews:

Related manuals for GB2581WS

Brands by name

Popular brands