GAF DecoTech RI 2000 Installation Instructions Manual Download Page 55

Page: 55 / 58

P a g e

DecoTech™ Solar System Codes and Standards (Model RI 2000)

The DecoTech™ Solar System includes the DecoTech™ Module Assembly (with PV laminate), the

underlayment system, and the DC/AC wiring components. Certifications for the DecoTech™ Module Assembly

(with PV laminate) and the underlayment system are mentioned below.

PV Laminate (frameless)

The SolarWorld laminate within the DecoTech™ Framed Module is certified to UL 1703 Standard for Flat-

Plate Photovoltaic Modules and Panels.

DecoTech™ Module Assembly

The DecoTech™ Module Assembly is tested and certified to comply with the following standard:

•

UL 2703

Standard for Mounting Systems, Mounting Devices, Clamping/Retention Devices, and

Ground Lugs for Use with Flat-Plate Photovoltaic Modules and Panels.

The top flashing and the top corner flashing are included in the UL 2703 listing. The starter bar, counter-

flashings, top flashing support, inner top flashing, and the MLPE are not included as part of the DecoTech™

UL 2703 electrical certification.

DecoTech™ Solar Array

The DecoTech™ Solar Array is tested and certified to comply with the following roofing standards:

•

UL 1897

Uplift Tests for Roof-Covering Systems

•

TAS 100

Test Procedure for Wind and Wind-Driven Rain Resistance of Discontinuous Roof Systems

The DecoTech™ Solar Module Assembly, in combination with the underlayment system, is classified as a

Class A fire rated system

, per UL 2703.

Underlayment System

StormGuard® Film-Surfaced Leak Barrier

is tested and certified to comply with the following standards:

•

ASTM D1970 – Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet

Materials Used as Steep Roofing Underlayment for Ice Dam Protection

•

ICC-ES Evaluation Report (ESR-1322)

•

Miami-Dade County Product Control approved

•

State of Florida Approved

•

UL Classified. See complete marking on product.

Summary of Contents for DecoTech RI 2000



























































Search results

Summary of Contents for DecoTech RI 2000

Reviews:

Related manuals for DecoTech RI 2000

Brands by name

Popular brands

GAF DecoTech RI 2000, Installation Instructions Manual

Search results

Summary of Contents for DecoTech RI 2000

Reviews:

Related manuals for DecoTech RI 2000

Brands by name

Popular brands