109
The GV-1 controls throttle when it is active, so the throttle will not obey any FailSafe settings preset for throttle in the
WUDQVPLWWHU$OZD\VVHWWKH)DLO6DIHVHWWLQJIRUWKH*9¶VRQRIIFKDQQHOWR2))7KLVZD\WKHJRYHUQRULVVKXWRII
and the throttle obeys the FailSafe throttle commands.
Expert Tip:
Mounting the GV-1 to the counter gear instead of the fan
GUDPDWLFDOO\VLPSOL¿HVLQVWDOODWLRQLQPDQ\PRGHOV
Setting example:
:KHQVSHHGDQG212))DUHXVLQJRQHVZLWFK
Governor Speed
Switch Position
(
Switch C
or Cond.)
Rate (%)
Adjustment from Tx.
RS1: OFF
UP
or
NORM
0
Use up to 0%.
(Governor speed display reads “off”.)
RS2: 1400
CNTR
or
IDL1
50
Speed adjusted by raising and lowering rate.
RS3: 1700
DOWN
or
IDL2
100
Speed adjusted by lowering rate.
*The relationship of the governor speed setting rS1~rS3 and the switch positions conforms to the table above.
*In throttle hold, always check that the governor is off.
*If the speed value rises when the cut switch is activated, reverse the “
DIR
” setting from
UP
to
DOWN
or vice versa.
GOAL of EXAMPLE:
STEPS:
INPUTS:
S e t u p a G V 1 g o v e r n o r t o u s e
b o t h c h a n n e l s i n t o t h e r e c e i v e r
a n d s w i t c h b e t w e e n t h e g o v e r n o r
settings automatically when changing
conditions. Consider setting the battery
Fail Safe settings and other helpful
functions on the GV-1 itself.
O p e n a n d a c t i v a t e t h e
G O V E R N O R
function.
for 1 second.
(If
BASIC
,
again.)
C
to
GOVERNOR
.
Activate the function.
C
to
MIX
.
to
ACT
.
Optional: change cut-off channel
to channel 8 and assign switch and
direction for on/off (channel 8).
C
to cut-
CH
to
+CH8
.
C
t o c u t -
S W
.
t o d e s i r e d
SWITCH
.
Optional: change switch assignment to
select governor settings.
E x : s e l e c t s w i t c h t h a t s e l e c t s t h e
conditions.
C
to
SW
.
to
Cond
.
Adjust governor speed settings per
switch position or condition as needed.
(Ex: defaults are fine.) Allows head
speed adjustment from transmitter.
C
to each
Cond
position.
or
as needed.
C
to next
Cond
position. Repeat.
Close the function.
Where next?
GYRO
: see p. 107.
Adjust FailSafe (
F/S
) settings (p. 50).
$GMXVWLGOHXSFROOHFWLYHSLWFKFXUYHIRUVDPHUDWHVRIFOLPEXSULJKWLQYHUWHG
See p. 101.
$GMXVW HOHYDWRUDLOHURQ UHVSRQVH WR ILW \RXU IO\LQJ VW\OH VHH
D/R
,
EXP
and
END
POINT
SWASH AFR
: p. 42, 39, 95.
