manualshive.com logo in svg

Fujitsu XG2000 Series, User Manual, Page: 55 / 315

Share
Download
Fujitsu XG2000 Series User Manual Download Page 55

XG2000 series User's Guide 

55/315 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2009 

4.11 RADIUS/ authentication   

RADIUS (Remote Authentication Dial In User Service) or TACACS (Terminal Access Controller Access Control System) is 
used to manage authentication, authorization, accounting remotely. XG2000 supports RADIUS/ authentication using 
PAP (User Password) for login authentication. An administrator can unify the authentications of various devices, which support 
RADIUS/ clients functions through a RADIUS/ server. 
 

4.11.1 RADIUS Attributes   

It displays RADIUS attributes. 

Attribute 

Value of attribute 

Content 

User-Name 

1 

The username to authenticate 

User-Password 

2 

Password to authenticate 

NAS-IP-ADDRESS 

4 

IP address of the device (management LAN) 

Service Type 

6 

AuthenticateOnly(8) 

NAS-Identifier 

32 

Hostname of the device 

 

4.11.2  Attributes   

It displays  attributes. 

Category 

Content 

action TAC_PLUS_AUTHEN_LOGIN 

(0x01) 

priv_lvl 

TAC_PLUS_PRIV_LVL_MIN  (0x00) 

authen_type TAC_PLUS_AUTHEN_TYPE_PAP 

(0x02) 

service TAC_PLUS_AUTHEN_SVC_LOGIN 

(0x01) 

user_len 

Size of user field 

rem_addr_len 0 
data_len 

Size of data field 

user 

Username to authenticate 

data 

Password of the user to authenticate 

 

Summary of Contents for XG2000 Series




























































































































































































































































































































Reviews:

No comments