manualshive.com logo in svg

Fujitsu XG2000 Series, User Manual, Page: 239 / 315

Share
Download
Fujitsu XG2000 Series User Manual Download Page 239

XG2000 series User's Guide 

239/315 

 

All Rights Reserved, Copyright (C) PFU LIMITED 2009 

z

 Rising 

Threshold 

Indicates the threshold upper limit (or the rising threshold). 

z

 Rising 

Event 

Indicates a number for the event notification if the value obtained exceeded the threshold 
limit. 
Event does not occur if the value is 0. 

z

 Falling 

Threshold 

Indicates the threshold lower limit (or the falling threshold). 

z

 Falling 

Event 

Indicates a number for the event notification if the value obtained dropped below the threshold 
limit. 
Event does not occur if the value is 0. 

z

 Owner 

Displays the owner name of the RMON alarm group. 

 
Event Information 

Displays the contents of the RMON event. 

z

 [Event 

1] 

Indicates an index number that identifies the RMON event entry. 

z

 Event 

Type 

log 

Displays the status of the RMON log entry creation when a RMON event occurred. 

−

 Enabled 

A RMON log entry was created. 

−

 Disabled 

No RMON log entry was created. 

Trap 

Displays the trap notification status. 

−

 Enabled 

SNMP trap notification occurs. 

−

 Disabled 

No SNMP trap notification occurs. 

z

 Trap 

Community 

Displays a community name for the SNMP trap. 

z

 Description 

Displays a character string that explains the RMON event entry. 

z

 Owner 

Displays the owner name of the RMON event entry. 

 

Summary of Contents for XG2000 Series




























































































































































































































































































































Reviews:

No comments