Fujitsu XG2000 Series User Manual Download Page 11

Page: 11 / 315

XG2000 series User's Guide

11/315

1.1 Features

The XG2000 series is a compact, 20-port 10 Gigabit Ethernet Layer 2 switch.
Special features of the XG2000 series are shown below:

Item

Function

Features

Throughput 400Gbit/s
Latency

350ns (Exclude latency of XFPs)

Switching mode

Either store-and-forward or cut-through is selectable.

MAC address learning table
size

16384 entries

MAC address learning

SVL (Shared VLAN Learning), IVL (Independent VLAN Learning),
user selectable.

Jumbo frame support

Up to 16KB (16128 bytes).

Flow control

IEEE802.3x compliant pause frame control. Possible to specify flow
control options for each port.

Storm control

Detects the broadcast storm status to prevent the traffic from
overflowing the network and avoid degrading overall system
performance.

Port security

Possible to restrict port access based on a source MAC address.

Ingress rate control

Supports by-port ingress rate control.

Port mirroring

Possible to monitor the incoming/outgoing traffic by port mirroring.

Basic Switch Functions

Link pass through

Possible to synchronize the link state of a monitored port with the
link state of a single or multiple ports.

Link aggregation
(Static and LACP)

Possible to increase bandwidth and redundancy. (Up to 10 ports for
each link).
Also supports IEE802.3ad LACP.

Scalability

Uplink Filter

Filtering multicast, broadcast and unlearned unicast frames from
leaf nodes to uplink. Possible to configure fat tree using several XG
series.

Redundancy IEEE802.1D

STP,

IEEE802.1w RSTP

Possible to make a redundant and loop-free network using Rapid
Spanning Tree Protocol (upward compatible with Spanning Tree
Protocol).

IEEE802.1Q VLAN

Max. 128 groups.

Filtering Ingress/egress filtering

VLAN support

Multiple VLAN

Possible to create multiple tag-based VLAN, with user VLAN tag
identifier.

IEEE802.1p QoS
DiffServ

Supports 4 traffic classes based on VLAN priority or DSCP
(DiffServ Code Point) of IPv4/IPv6.

QoS

Scheduling Strict,

DRR(Deficit Round Robin), DRR

Multi-cast support

IGMP snooping

Prevents unnecessary forwarding of multicast traffic to ports to
reduce unnecessary multicast traffic.

Traffic statistics

Possible to analyze traffic and errors, using traffic statistics.

Network Management

SNMP agent

Can be used in conjunction with an SNMP manager, supporting
MIBs, including Standard MIB, Bridge MIB, and RMON MIB.

Console by
serial/management LAN

Dedicated management LAN is isolated from the serial interface
and 10 Gigabit ports to secure the device.

CLI

Allows the user to provide environment settings and operation
management using command line interface (CLI).

Operation
management

Remote authentication

RADIUS and

Summary of Contents for XG2000 Series
























































































































































































































































































































Search results

Summary of Contents for XG2000 Series

Reviews:

Fujitsu XG2000 Series, User Manual, Page: 11 / 315

Search results

Summary of Contents for XG2000 Series

Reviews: