Fujitsu PRIMERGY RX2530 M4 Operating Manual Download

Page: 68 / 88

Operating Manual

RX2530 M4

Starting up and operation

LAN indicators

Figure 16: LAN indicators

Depending on the BIOS settings, the shared LAN connector may also be
used as a management LAN connector. For further information, please
refer to the corresponding BIOS Setup Utility reference manual.

Pos. Indicator

Status

Description

LAN
link/transfer
indicator

green on

A LAN connection has been
established.

off

LAN is not connected.

green
flashing

LAN data transfer is in progress.

LAN speed
indicator

yellow on

Data traffic at a transfer rate of 1 Gbit/s.

green on

Data traffic at a transfer rate of
100 Mbit/s.

off

Data traffic at a transfer rate of
10 Mbit/s.

Summary of Contents for PRIMERGY RX2530 M4

























































































Search results

Summary of Contents for PRIMERGY RX2530 M4

Reviews:

Related manuals for PRIMERGY RX2530 M4

Brands by name

Popular brands

Fujitsu PRIMERGY RX2530 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY RX2530 M4

Reviews:

Related manuals for PRIMERGY RX2530 M4

Brands by name

Popular brands