Fujitsu PRIMERGY RX2530 M4 Operating Manual Download

Page: 87 / 88

RX2530 M4

Operating Manual

Troubleshooting and tips

8.9

Added drive reported as defective

RAID controller is not configured for this drive

The drive was probably installed when the system was switched off.

Reconfigure the RAID controller for the drive using the corresponding utility.
Information is provided in the documentation for the RAID controller.

Remove and reinstall the drive while the system is switched ON.

If the drive continues to be shown as defective, then replace it.

8.10 Error message on screen

The meaning of the error message is explained in the documentation for the
relevant components and programs on the Fujitsu manuals server.

8.11

Expansion cards or onboard devices not
recognized

When an expansion card is added, other expansion cards or onboard devices
might not be recognized.

Reinstall the drivers for the expansion cards or onboard devices that are not
recognized.

Summary of Contents for PRIMERGY RX2530 M4

























































































Search results

Summary of Contents for PRIMERGY RX2530 M4

Reviews:

Related manuals for PRIMERGY RX2530 M4

Brands by name

Popular brands

Fujitsu PRIMERGY RX2530 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY RX2530 M4

Reviews:

Related manuals for PRIMERGY RX2530 M4

Brands by name

Popular brands