Fujitsu MAU3036NC Page 84 Product/Maintenance Manual Download | Manualshive

Page: 84 / 130

background image

5-12

C141-E205

5.5 Connecting

Cables

Connect the IDD and system with the following cables. See Section 4.3 for further details of the
requirements for IDD connector positions and connecting cables.

•

Power cable

•

SCSI cable

•

External operator panel cable (if required for NP model)

The general procedures and notes on connecting cables are described below. Especially, pay
attention to the inserting orientation of each cable connector.

CAUTION

Damage
1. Make sure that system power is off before connecting or disconnecting

cables.

2. Do not connect or disconnect cables when power is on. (except NC

model)

a) Connect power cable.

b) Connect the external operator panel (if required for NP model).

c) Connect the SCSI cable.

d) Fix the cables so that they do not touch the DE and PCAs, or so that the smooth flow of the

cooling air in the system cabinet is assured.

CAUTION

Damage
1.

Be careful of the insertion orientations of the SCSI connectors. With the
system in which terminating resistor power is supplied via the SCSI
cable, if the power is turned on, the overcurrent protection fuse of the
terminating resistor power supplier may be blown or the cable may be
burnt if overcurrent protection is not provided.

When the recommended parts listed in Table 4.2 are used, inserting the
cables in the wrong orientation can be prevented.

2. To connect SCSI devices, be careful of the connection position of the

cable. Check that the SCSI device with the terminating resistor is the last
device connected to the cable.

«
...
82
83
84
85
86
...
»

Summary of Contents for MAU3036NC



































































































































Reviews:

No comments

Related manuals for MAU3036NC

DS8000 - ADDITIONAL INFORMATION

Brand: IBM Pages: 5

System Storage TS7600 ProtecTIER Series

Brand: IBM Pages: 132

Brand: IBM Pages: 188

Brand: Edirol Pages: 1

HAWK 2 ST11900W

Brand: Seagate Pages: 40

Brand: Seagate Pages: 54

Brand: Hama Pages: 4

Brand: BOH Enviromental Pages: 20

301300U - Ethernet Disk NAS Server

Brand: LaCie Pages: 62

Paletto 00108043

Brand: Hama Pages: 4

Brand: Nexsan Pages: 6

Beside Storage Pantry

Brand: Haworth Pages: 6

Brand: FRANKLINWH Pages: 81

Brand: Geekworm Pages: 13

Citrix XenServer

Brand: Fujitsu Pages: 23

Brand: Fujitsu Pages: 12

Brand: Fujitsu Pages: 14

Brand: Fujitsu Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands