manualshive.com logo in svg

Fujitsu MAU3036NC, Product/Maintenance Manual, Page: 123 / 130

Share
Download
Fujitsu MAU3036NC Product/Maintenance Manual Download Page 123

C141-E205 

IN-1 

INDEX  

+12 VDC .........................................................4-8 
1-1x-xx ............................................................7-4 
16-bit SCSI ID external input........................4-16 
16-bit SCSI interface connector ....................4-14 
3-0C-03 ...........................................................7-4 
3-1x-xx ............................................................7-4 
4-40-xx ............................................................7-4 
4-44-xx ............................................................7-4 
4-C4-xx ...........................................................7-4 
5-2x-xx ............................................................7-4 
5-3D-00 ...........................................................7-4 
5-90-00 ............................................................7-4 
68-pin type LVD 16-bit SCSI ........................ B-3 
8-bit SCSI/16-bit SCSI....................................1-2 

A 

AC noise filter ...............................................4-11 
actuator............................................................1-7 
addressing of peripheral device.......................1-9 
air circulation (recirculation filter, breather 

filter) 1-7 

allowable input voltage and current ................4-8 
alternate area ...................................................3-9 
alternate block allocation ..............................3-10 
alternate block allocation by REASSIGN 

BLOCKS command.................................3-13 

alternate block allocation during FORMAT 

UNIT command execution ......................3-11 

alternate cylinder .............................................3-4 
alternate spare area ..........................................3-3 
automatic alternate block allocation..............3-13 
automatic alternate block allocation at write 

operation ..................................................3-14 

automatic alternate block reassignment ..........1-4 

B 

B-44-xx ...........................................................7-4 
B-47-xx ...........................................................7-4 
B-49-00 ...........................................................7-4 
B-4D-xx ..........................................................7-4 
B-4E-00 ...........................................................7-4 
basic operation test ..........................................6-5 
BCRC ..............................................................3-7 
block address of user space .............................3-9 
bock descriptor ..............................................5-17 
 

C 

cache feature....................................................1-3 
caching parameter .........................................5-22 
changing revision number in field...................6-9 
check before mounting ..................................5-11 
check items at illegal operation .....................5-13 
checking at abnormal end..............................5-17 
checking procedure .......................................5-14 
checking SCSI connection .........5-14, 5-15, 5-16 
CN1 ........................................................ B-2, B-3 
CN2 setting terminal ......................................A-2 
command queuing feature ...............................1-4 
compactness ....................................................1-2 
confirming initial operation...........................5-13 
confirming operation after installation and 

preparation for use ...................................5-13 

connecting cable............................................5-12 
connection .......................................................5-3 
connector signal allocation............................. B-1 
continuous block processing ...........................1-3 
control mode parameter.................................5-22 
controller circuit ..............................................1-7 
current waveform ............................................4-8 
cylinder configuration .....................................3-2 

D 

data format ......................................................3-1 
data space ........................................................3-1 
default mode setting (by CHANGE 

DEFINITION command).........................5-10 

defect list .......................................................3-10 
defect management........................................3-10 
defective block slipping ..................................1-4 
definition of sense data....................................7-3 
delivery............................................................5-2 
diagnosis..........................................................1-5 
diagnostic ........................................................6-1 
diagnostic and maintenance ............................6-1 
diagnostic test................................................6-12 
disconnection/reconnection parameter ..........5-21 
disk ..................................................................1-7 
disk drive troubleshooting .............................6-15 
disk read error .................................................7-4 
dismounting drive..........................................5-23 

Summary of Contents for MAU3036NC



































































































































Reviews:

No comments