Fujitsu MAU3036NC Page 104 Product/Maintenance Manual Download

Page: 104 / 130

6-8

C141-E205

See Section 5.1 for notes on packing and handling when returning the disk drive.

6.2.3 Maintenance

levels

If a disk drive is faulty, replace the whole disk drive since repair requires special tools and
environment. This section explains the two maintenance levels.

(1)

Field maintenance (disk drive replacement)

•

This replacement is done at the user's site.

•

Replacement uses standard tools.

•

Replacement is usually done by the user, retail dealer, distributor, or OEM engineer.

(2)

Factory maintenance (parts replacement)

•

This replacement can only be done by Fujitsu.

•

Replacement includes maintenance training and OEM engineer support. OEM engineers
usually support retail dealers and distributors.

•

Replacement uses factory tools and test equipment.

Summary of Contents for MAU3036NC



































































































































Search results

Summary of Contents for MAU3036NC

Reviews:

Related manuals for MAU3036NC

Brands by name

Popular brands

Fujitsu MAU3036NC, Product/Maintenance Manual

Search results

Summary of Contents for MAU3036NC

Reviews:

Related manuals for MAU3036NC

Brands by name

Popular brands