Fujitsu MAU3036NC Page 59 Product/Maintenance Manual Download | Manualshive

Page: 59 / 130

background image

C141-E205

4-9

c) In a system which does not use the terminating resistor power supply signal (TERMPWR) on

the SCSI bus, the requirements for +5 VDC given in Figure 4.10 must be satisfied between the
IDD and the SCSI device with the terminating resistor circuit.

Figure 4.10 Power on/off sequence (2)

d) Between the IDD and other SCSI devices on the SCSI bus, the +5 VDC power on/off sequence

is as follows:

•

In a system with its all SCSI devices designed to prevent noise from leaking to the SCSI
bus when power is turned on or off, the power sequence does not matter if the
requirement in b) or c) is satisfied.

•

In a system containing an SCSI device which is not designed to prevent noise from
leaking to the SCSI bus, the requirement given in Figure 4.11 must be satisfied between
that SCSI device and the IDD.

Figure 4.11 Power on/off sequence (3)

SCSI devices
without noise
leaking designed

SCSI devices with
the terminating
resistor

«
...
57
58
59
60
61
...
»

Summary of Contents for MAU3036NC



































































































































Reviews:

No comments

Related manuals for MAU3036NC

Brand: Backyard Pages: 63

TOWERRAID TR5M1

Brand: Sans Digital Pages: 82

HIMALAYA 100.S/2/CC

Brand: garofalo Pages: 12

Brand: G&T SALES Pages: 2

Brand: Dancover Pages: 66

Brand: Bull Pages: 50

My Passport Essential SE

Brand: Western Digital Pages: 2

Brand: Western Digital Pages: 2

Cheetah 15K.7 FC

Brand: Seagate Pages: 90

PREMIER GAMT41HWJG

Brand: Gladiator Pages: 24

Brand: Clarke Pages: 4

EonStor DS B Series

Brand: Infotrend Pages: 157

Brand: 3Ware Pages: 50

Brand: Panasonic Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands