manualshive.com logo in svg

Fujitsu MAU3036NC, Product/Maintenance Manual, Page: 45 / 130

Share
Download
Fujitsu MAU3036NC Product/Maintenance Manual Download Page 45

C141-E205 

3-11 

 

The alternate block allocation is executed by the FORMAT UNIT command, the REASSIGN 
BLOCKS command, or the automatic alternate block allocation.  Refer to Chapter 3 “Command 
Specification” and Subsection 5.3.2 “Auto alternate block allocation processing” in the SCSI 
Logical  Interface Specifications for details of specifications on these commands.  The logical data 
block is allocated to the next physically continued sectors after the above sector slip treatment is 
made.  On the other hand, the logical data block is allocated to spare sectors which are not 
physically consecutive to the adjacent logical data blocks.  If a command which processes several 
logical data blocks is specified, the IDD processes those blocks in ascending order of logical data 
block. 

 
(1) 

Alternate block allocation during FORMAT UNIT command execution 

 

When the FORMAT UNIT command is specified, the allocation of the alternate block to those 
defective sectors included in the specified lists (P, G, or D) is continued until all spare sectors in 
the same cell are used up.  When they are used up, unused spare sectors in the alternate cylinder 
are allocated to the subsequent sectors in the cylinder by means of alternate sector treatment.  
Figure 3.7 is examples of the alternate block allocation during the FORMAT UNIT command 
execution. 

 

Summary of Contents for MAU3036NC



































































































































Reviews:

No comments