Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Page 89 Product/Maintenance Manual Download | Manualshive

Page: 89 / 130

background image

C141-E185

5-17

(2)

Checking at abnormal end

a) When sense data can be obtained with the REQUEST SENSE command, analyze the sense

data and retry recovery for a recoverable error. Refer to Chapter 5 of SCSI Logical Interface
Specifications for further details.

b) Check the following items for the SCSI cable connection:

•

All connectors including other SCSI devices are connected correctly.

•

The terminating resistor is mounted on both ends of the cable.

•

Power is connected to the terminating resistor.

c) Check the setting of the terminals. Note that the checking procedure of SCSI connection

differs depending on the setting of the motor start mode and UNIT ATTENTION report mode.

5.6.3Formatting

Since the disk drive is formatted with a specific (default) data format for each model (part number)
when shipped from the factory, the disk need not be formatted (initialized) when it is installed in
the system.

However, when the system needs data attributes different from the default format, all recording
surface of the disk must be formatted (initialized) according to the procedures below.

The user can change the following data attributes at initialization:

•

Logical data block length

•

Number of logical data blocks or number of cylinders in the user space

•

Alternate spare area size

This section outlines the formatting at installation. Refer to Chapters 3 and 6 of SCSI Logical
Interface Specifications for further details.

(1)

MODE SELECT/MODE SELECT EXTENDED command

Specify the format attributes on the disk with the MODE SELECT or MODE SELECT
EXTENDED command. The parameters are as follows.

a. Block descriptor

Specify the size (byte length) of the logical data block in the "data block length" field. To
explicitly specify the number of logical data blocks, specify the number in the "number of data
blocks" field. Otherwise, specify 0 in "number of data blocks" field. In this case, the number
of logical data blocks after initialization is determined by the value specified in the format
parameter (page code = 3) and drive parameter (page code = 4).

«
...
87
88
89
90
91
...
»

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Reviews:

No comments

Related manuals for MAS3184NC - Enterprise 18.4 GB Hard Drive

G-DRIVE mobile USB

Brand: G-Technology Pages: 13

Solid Stainless Steel Shelving

Brand: Omega Pages: 2

Brand: Acard Pages: 54

Brand: Kingston Technology Pages: 2

Brand: IBM Pages: 68

StorageTek T10000D

Brand: Oracle Pages: 51

Brand: IBM Pages: 104

BASIC PRO SERIES

Brand: Borroughs Pages: 17

Brand: Magnusson Pages: 18

Brand: HGST Pages: 51

IBM Half-high LTO Generation 3

Brand: Lenovo Pages: 13

Brand: Lenovo Pages: 37

Brand: Lenovo Pages: 46

Brand: Lenovo Pages: 20

IBM Storwize V7000

Brand: Lenovo Pages: 30

Brand: Lenovo Pages: 56

Brand: Lenovo Pages: 4

Brand: Lenovo Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands