manualshive.com logo in svg

Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive, Product/Maintenance Manual, Page: 46 / 130

Share
Download
Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Product/Maintenance Manual Download Page 46

3-12

C141-E185

The alternate block allocation is executed by the FORMAT UNIT command, the REASSIGN
BLOCKS command, or the automatic alternate block allocation.  Refer to OEM Manual–SCSI
Logical Specifications–for details of specifications on these commands.  The logical data block is
allocated to the next physically continued sectors after the above sector slip treatment is made.  On
the other hand, the logical data block is allocated to spare sectors which are not physically
consecutive to the adjacent logical data blocks.  If a command which processes several logical data
blocks is specified, the IDD processes those blocks in ascending order of logical data block.

(1)

Alternate block allocation during FORMAT UNIT command execution

When the FORMAT UNIT command is specified, the allocation of the alternate block to those
defective sectors included in the specified lists (P, G, or D) is continued until all spare sectors in
the same cell are used up.  When they are used up, unused spare sectors in the alternate cylinder
are allocated to the subsequent sectors in the cylinder by means of alternate sector treatment.
Figure 3.7 is examples of the alternate block allocation during the FORMAT UNIT command
execution.

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Reviews:

No comments