manualshive.com logo in svg

Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive, Product/Maintenance Manual, Page: 104 / 130

Share
Download
Fujitsu MAS3184NC - Enterprise 18.4 GB Hard Drive Product/Maintenance Manual Download Page 104

6-8

C141-E185

See Section 5.1 for notes on packing and handling when returning the disk drive.

6.2.3Maintenance levels

If a disk drive is faulty, replace the whole disk drive since repair requires special tools and
environment.  This section explains the two maintenance levels.

(1)

Field maintenance (disk drive replacement)

•

 

This replacement is done at the user's site.

•

 

Replacement uses standard tools.

•

 

Replacement is usually done by the user, retail dealer, distributor, or OEM engineer.

(2)

Factory maintenance (parts replacement)

•

 

This replacement can only be done by Fujitsu.

•

 

Replacement  includes  maintenance  training  and  OEM  engineer  support.  OEM  engineers
usually support retail dealers and distributors.

•

 

Replacement uses factory tools and test equipment.

Summary of Contents for MAS3184NC - Enterprise 18.4 GB Hard Drive



































































































































Reviews:

No comments